Whirlpool WHESFC Скачать руководство пользователя

Страница: 15 / 26

Customizing Features / Options

RECHARGE initiated

RECHARGE

The RECHARGE button is used to initiate an immedi-

ate recharge.

. Press and hold the RECHARGE button until the

words “RECHARGE", “SERVICE" and “FILL" flash

in the display.

SET SALT LEVEL

The water conditioner has a salt monitor indicator

light to remind you to add salt to the storage tank.

NOTE:

You must set salt level each time salt is added

to the water conditioner.

To set this monitor system:

. Lift the salt lid and level the salt in the storage tank.

. The salt level scale, on the brinewell inside the

tank, has numbers from 0 to 8. Observe the high-

est number the leveled salt is at, or closest to.

. Press the SET SALT LEVEL button until black

ovals correspond to the salt level number (See

Figure 22). At level 2 or below, the “Check Salt

Level" LED indicator will flash.

FIG. 20

The conditioner enters the fill cycle of regeneration

right away. “RECHARGE” will flash during the regen-

eration. When completed, full water conditioning

capacity is restored. While water conditioner is run-

ning a recharge, the time remaining until the recharge

is completed will show in the display during all cycles

except for the Fill cycle.

NOTE

: Avoid using hot water while the conditioner is

regenerating, because the water heater will

refill with bypass hard water.

RECHARGE SCHEDULED

If you do not want to start an immediate recharge, but

would like to schedule an extra recharge at the next

preset recharge time, do the following:

. Press and release (do not hold) the RECHARGE

button.

FIG. 21

The words “RECHARGE SCHEDULED" flash in the

display, and the conditioner will recharge at the next

recharge time. The word “RECHARGE" will flash dur-

ing the regeneration. When completed, full water

conditioning capacity is restored.

RECHARGE scheduled

TANK LIGHT

The water conditioner is equipped with a tank light for

viewing the salt level in the brine tank. Push the tank

light button on the electronic control once, and the

tank light will turn on. Pushing the tank light button

again will turn the light off. The tank light will auto-

matically turn off after a period of 15 minutes if the

tank light button is not used to turn it off.

If you want to turn the salt monitor off, press the SET

SALT LEVEL button until “SALT LEVEL OFF” shows

in the display (See Figure 23).

FIG. 23

FIG. 22

LEVEL

SALT

Brinewell

Numbers

Salt

Level

Содержание WHESFC



























Результаты поиска

Содержание WHESFC

Отзывы:

Похожие инструкции для WHESFC

Бренды по названию

Популярные бренды

Whirlpool WHESFC, Инструкция по установке и эксплуатации

Результаты поиска

Содержание WHESFC

Отзывы:

Похожие инструкции для WHESFC

Бренды по названию

Популярные бренды