Whirlpool WHESFC Скачать руководство пользователя

Страница: 13 / 26

PRESS TO SCHEDULE

HOLD TO START

PROGRAM

RECHARGE

SET

SALT

LEVEL

TANK

LIGHT

OPERATING (Steady)

LOW SALT (Flashing)

Programming the Water Conditioner

FIG. 16

Questions? Call Toll Free 1-866-986-3223

Monday- Friday, 8 AM - 7 PM EST

or visit www.whirlpoolwatersofteners.com

When you call, please be prepared to provide the model and serial number,

found on the rating decal, typically located on the rim below the salt lid hinges.

FIG. 15

UP button

Display

TANK LIGHT

button

SET SALT LEVEL

button

PROGRAM button

DOWN button

RECHARGE button

STATUS LIGHT

(see below)

PROGRAM THE CONDITIONER

When the power supply is plugged into the electrical

outlet, the model code (LLFC) and a test number

(example: J38), are briefly shown in the display.

Then the words “CURRENT TIME” appear and 12:00

PM begins to flash.

SET TIME OF DAY

If the words “CURRENT TIME" do not show in the

display, press the PROGRAM button until they do.

. Press the

UP or

DOWN buttons to set the

present time. Up moves the display ahead; down

sets the time back. Be sure AM or PM is correct.

NOTE:

Press buttons and quickly release to slowly

advance the display. Hold the buttons down

for fast advance.

continued on next page

STATUS LIGHT

When the water conditioner is connected to electrical

power, the status light on the control panel will oper-

ate as follows:

Light flashing slowly, along with the salt level

indicators in the display

- The salt monitor sys-

tem indicates a low salt level and needs to be set.

See “Set Salt Level” on Page 15.

Light flashing slowly, along with the words

“SCHEDULED CLEAN” in the display

- Four

months have elapsed on the system’s timer since

start up or the last reset. This is a reminder to use

Whirlpool

WHE-WSC Water Softener Cleanser

three times a year. To reset the timer, press any

button on the control panel and the flashing words

will disappear. The status light will stop flashing,

unless the system is also low on salt (see above).

Light flashing rapidly, with “CURRENT TIME”

shown in the display and the clock flashing

slowly

- The present time needs to be set, either

during initial start up or after a long power outage.

See “Set Time of Day”, at right.

Light flashing rapidly, with “Err” shown in the

display

- The electronic self-diagnostics have

detected a problem. See “Troubleshooting” on

Page 20.

Light on steady (not flashing)

- The system has

power applied and does not require any attention.

Содержание WHESFC



























Результаты поиска

Содержание WHESFC

Отзывы:

Похожие инструкции для WHESFC

Бренды по названию

Популярные бренды

Whirlpool WHESFC, Инструкция по установке и эксплуатации

Результаты поиска

Содержание WHESFC

Отзывы:

Похожие инструкции для WHESFC

Бренды по названию

Популярные бренды