PAGE 6
FOR SERVICE TECHNICIAN’S USE ONLY
DO NOT REMOVE OR DESTROY
QUICK DIAGNOSTIC TEST
NOTE:
The Service Diagnostic mode must be
activated before entering the Quick Diagnostic
Test; see procedure on page 4. If, at any point,
the user presses the POWER button, the
washer exits to standby mode.
Active Fault Code Display
in Quick Diagnostic Test
If the display begins flashing while in the Quick
Diagnostic Test, it is displaying an active fault
code. Active fault codes are codes that are
currently detected. Only one active fault code
can be displayed at a time.
i
Press power button at any time to exit
i
Entry Procedure
To enter the Quick Diagnostic Test, press and
release the
2nd
button used to activate the
Service Diagnostic mode. The power button
indicator turns on and the start button indicator
begins to flash. Press the
START
button to
perform the Quick Diagnostics tests listed below.
Each test phase is indicated on the display.
IMPORTANT:
If entry into Quick Diagnostics
is performed too quickly after activating the
Service Diagnostic mode, the test will not start.
Exit Procedure
To exit Quick Diagnostics, press the
POWER
button, or press and hold the
1st
button used
to activate Service Diagnostic mode for 5
seconds.
TEST
PHASE
WASHER FUNCTION
COMPONENT
PHASE ENDS…
C00 *
Door lock motor is actuated. Door
unlocks, and then locks again.
Pump is activated for 15 seconds.*
?1141&-;56(/
?4$,07/2
*
on completion ON
#
.
C01 †
steam models
10.;
Heater is turned on.
6($/8$.8(,5$&67$6('
?($6(4
?6($/!
alve
?
Te
/2(4$674((0514
10&1/2.(6,1014$6-(;24(55
C02
Cold water valve will actuate.
?1.'
Water
!$
lve
?.19(6(46($/10.;
)
10&1/2.(6,1014$6-(;24(55
C03
,52(05,0*5;56(/,55(6616+(4(9$5+
position #1.
?,52(05(4161
r
?,52(05(4106$&6
on completion ON
#
.
C04
Hot water valve will actuate.
?16
Wa
6(4!
alve
?.19(6(46($/10.;
)
10&1/2.(6,1014$6-(;24(55
C05
Drum rotates clockwise at wash speed.
?161
r
?161410641. 0,6
10&1/2.(6,1014$6-(;24(55
C06 ‡
Heater is turned on to heat water
to pre-set temperature level.
Drum rotates clockwise and counter-
clockwise at wash speed.
Water valve is activated to fill drum to
minimum water volume required to
9$5+)6+(4(,5(017*+9$6(4,06+(
drum, the water valve will not turn on.)
?($6(4
?
Te
/2(4$674((0514
?1614
?161410641. 0,6
?1.'
Water
!$.8(,)0(('('
?4(5574((0514 9,6&+
10&1/2.(6,1014$6-(;24(55
C07
Drain Pump is actuated until there is no
9$6(4,06+(5;56(/@2.75$0$'',6,10$.
15 seconds.
?4$,07/2
?4(5574((0514 9,6&+
10&1/2.(6,1014$6-(;24(55
Drum rotates counter-clockwise from 35
rpm > 100 rpm > 150 rpm > 100 rpm in
< /,076(5
?1614
?161410641. 0,6
on completion ON
#
.
Drum rotates counter-clockwise at
maximum speed.
Door lock motor is actuated. Door
unlocks.
?1614
?161410641. 0,6
?1141&-;56(/
on completion or press of the
power button.
C08
QUICK DIAGNOSTIC TEST
QUICK DIAGNOSTIC TEST NOTES:
*C00
– For STEAM models, the drain pump is activated as part of the APS (Analog Pressure Sensor) calibration routine. For NON-STEAM
models, the drain pump is only activated if the CCU detects a significant amount of water in the tub. Drain time will depend on water in tub.
† C01
– This test phase is performed only on STEAM models. NON-STEAM models skip this test.
‡ C06
– This test will run until a pre-set temperature level is reached. Water temperature will affect the duration of the test.