background image

Steps in Final Location

1. Slide the washer to its final location.
2. Tilt the washer forward until the rear of the washer is at least 

10.2 cm (4") off the floor. You may hear the self-adjusting rear 
feet click into place. Lower the washer to the floor.  

3. Check the levelness of the washer by placing a level on the 

top edges of the washer, first side to side, then front to back. 

4. If the washer is not level, move the washer out slightly, tip 

back, prop up the front of the washer with the wood block and 
adjust the feet up or down as necessary by twisting the feet. 
Turn the feet clockwise to raise the washer or 
counterclockwise to lower the washer. Repeat steps 
1 through 4 until washer is level. 

5. After the washer is in its final location and level, use a 14 mm 

or 

⁹⁄₁₆

" open-end wrench to turn the nuts counterclockwise on 

the feet tightly against the washer cabinet. 
IMPORTANT: If the nuts are not tight against the washer 
cabinet, the washer may vibrate. 

Complete Installation

1. Check the electrical requirements. Be sure that you have the 

correct electrical supply and the recommended earthing 
method. See “Electrical Requirements.”

2. Check that all parts are now installed. If there is an extra part, 

go back through the steps to see which step was skipped.

3. Check that you have all of your tools.
4. Check that the yellow shipping strap was completely removed 

from the lower back of the washer.

5. Dispose of/recycle all packaging materials. 
6. Check that the water faucets are on.
7. Check for leaks around faucets and inlet hoses. 

8. Plug into an earthed outlet.
9. Remove the protective film on the console and any tape 

remaining on the washer.

10. Read “Washer Use” in the Washer User Instructions.
11. To test and to clean your washer, measure 

¹₂

 of the normal 

recommended amount of powdered or liquid detergent and 
pour it into the washer basket or detergent dispenser (on 
some models). Close the lid. Select any cycle, and then pull 
the cycle control knob out to start the washer. Allow it to 
complete one whole cycle.

A. Self-adjusting feet

A

10.2 cm
(4")

WARNING

Electrical Shock Hazard

Electrically earth this appliance.

Do not use an extension cord or an electrical portable 
outlet device.

Failure to follow these instructions can result in death, 
fire, or electrical shock.

W10038090

© 2006 Whirlpool Corporation.

Benton Harbor, Michigan 49022

4/06

Printed in U.S.A.

Содержание W10038090









Отзывы: