background image

4

If connecting to a 4-wire system:

This range is manufactured with the ground connected to the 
cabinet. The ground must be revised so the green ground wire of 
the 4-wire power supply cord is connected to the cabinet. See 
“Electrical Connection.”

Grounding through the neutral conductor is prohibited for new 
branch-circuit installations (1996 NEC); mobile homes; and 
recreational vehicles, or an area where local codes prohibit 
grounding through the neutral conductor.

When a 4-wire receptacle of NEMA Type 14-50R is used, a 
matching UL listed, 4-wire, 250-volt, 40- or 50-amp, range power 
supply cord (pigtail) must be used. This cord contains 4 copper 
conductors with ring terminals or open-end spade terminals with 
upturned ends, terminating in a NEMA Type 14-50R plug on the 
supply end. 

The fourth (grounding) conductor must be identified by a green or 
green/yellow cover and the neutral conductor by a white cover. 
Cord should be Type SRD or SRDT with a UL listed strain relief 
and be at least 4 ft (1.22 m) long.

The minimum conductor sized for the copper 4-wire power 
cord are:

40-amp circuit
2 No.-8 conductors
1 No.-10 white neutral
1 No.-8 green grounding

If connecting to a 3-wire system:

Local codes may permit the use of a UL listed, 3-wire, 250-volt, 
40- or 50-amp range power supply cord (pigtail). This cord 
contains 3 copper conductors with ring terminals or open-end 
spade terminals with upturned ends, terminating in a NEMA Type 
10-50P plug on the supply end. Connectors on the appliance end 
must be provided at the point the power supply cord enters the 
appliance. This uses a 3-wire receptacle of NEMA Type 10-50R.

INSTALLATION INSTRUCTIONS

Unpack Range

1. Remove shipping materials, tape and protective film from 

range. Remove oven racks and parts package from inside 
oven.

2. Do not remove the shipping base at this time.

3. On Ranges Equipped with Storage Drawers:

Remove the storage drawer. Use a

 ³⁄₈

" drive ratchet to lower 

the rear leveling legs one-half turn. Use a wrench or pliers to 
lower front leveling legs one-half turn. 

On Ranges Equipped with Warming Drawers:

Use a wrench or pliers to lower the front and rear leveling legs 
one-half turn.

4-wire receptacle (14-50R)

3-wire receptacle (10-50R)

A. Shipping base

WARNING

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

A

A.

³⁄₈

" drive ratchet

B. Rear leveling leg
C. Wrench or pliers
D. Front leveling leg

A. Rear leveling leg
B. Front leveling leg

C. Wrench or pliers

A

B

C

D

A

B

C

Содержание RF265LXTS













Отзывы: