Whirlpool LE18 Скачать руководство пользователя страница 12

Страница: 12 / 24

Programming the Water Softener

CLEAN REMINDER

The screen in Figure 16 appears, with “CLEAn” flash-

ing in the display, when four months have elapsed on

the system’s timer since start up or the last reset.

FIG. 16

This is a reminder to use Whirlpool

WHE-WSC

Water Softener Cleanser three times a year. To reset

the timer, press any button on the control panel and

“CLEAn” will disappear.

PROGRAM THE SOFTENER

When the power supply is plugged into the electrical

outlet, the model code (LE18) and a software version

number (example: J3.9), are briefly shown in the

display. Then the words “PRESENT TIME” appear

and 12:00 PM begins to flash.

FIG. 15

UP button

DOWN

button

Display

RECHARGE

button

PROGRAM

button

Questions? Call Toll Free 1-866-986-3223

or visit

whirlpoolwatersolutions.com

When you call, please be prepared to provide the model and serial number,

found on the rating decal, typically located on the rim below the salt lid.

SET TIME OF DAY

If the words “PRESENT TIME” do not show in the

display, press the PROGRAM button until they do.

. Press the

UP or

DOWN buttons to set the

present time. Up moves the display ahead; down

sets the time back. Be sure AM or PM is correct.

NOTE:

Press buttons and quickly release to slowly

advance the display. Hold the buttons down

for fast advance.

SET WATER HARDNESS NUMBER

. Press the PROGRAM button once again to display

a flashing “25” and the word “HARDNESS”.

FIG. 17

FIG. 18

. Press the

UP or

DOWN buttons to set your

water’s hardness number.

Содержание LE18

























Результаты поиска

Содержание LE18

Отзывы:

Похожие инструкции для LE18

Бренды по названию

Популярные бренды

Whirlpool LE18, Описание, установка и руководство по эксплуатации

Результаты поиска

Содержание LE18

Отзывы:

Похожие инструкции для LE18

Бренды по названию

Популярные бренды