background image

2-1

If codes permit and a separate ground wire
is used, it is recommended that a qualified
electrician determine that the ground path
is adequate.

Do not ground to a gas pipe.

Check with a qualified electrician if you are
not  sure  whether  the  cooktop  is  properly
grounded.

Do not have a fuse in the neutral or ground
circuit.

240 VOLT COOKTOP

1.

A  three-wire  or  four-wire,  single  phase,
240-volt, 60-Hz, AC-only electrical supply
is required on a separate, 40-ampere cir-
cuit, fused on both sides of the line. A time-
delay  fuse  or  circuit  breaker  is  recom-
mended. The fuse size must not exceed
the circuit rating of the appliance specified
on the model/serial rating plate located on
the bottom of the cooktop.

THE COOKTOP MUST BE CONNECTED
WITH COPPER WIRE ONLY.

INSTALLATION HIGHLIGHTS

ELECTRICAL REQUIREMENTS

2.

Wire sizes and connections must conform
to the requirements of the National Electri-
cal  Code  ANSI/NFPA  70  —  latest  edi-
tion**, or CSA Standards C22.1-94, Cana-
dian Electrical Code, Part 1 and C22.2 No.
0-M91  —  latest  edition***  and  all  local
codes and ordinances.

3.

The cooktop should be connected directly
to the fused disconnect or circuit breaker
box through flexible, armored or non-me-
tallic sheathed, copper cable. The flexible,
armored  cable  extending  from  the  fuse
box or circuit breaker box should be con-
nected directly to the junction box.

4.

Locate the junction box to allow as much
slack  as  possible  between  the  junction
box and the cooktop so that the cooktop
can be moved if servicing is ever neces-
sary. 

Do Not cut the conduit.

5.

A U.L. -  or C.S.A.-listed conduit connector
must be provided at each end of the power
supply  cable  (at  the  cooktop  and  at  the
junction box).

Copies of the standards listed above may be
obtained from:

  **National Fire Protection Association
     Batterymarch Park
     Quincy, Massachusetts 02269

  ***Canadian Standard Association
       178 Rexdale Boulevard
       Etobicoke, Ontario M9W 1R3

All manuals and user guides at all-guides.com

Содержание KECS100G











































Отзывы: