18
3.
Press the tab down on the right side, and lift tab up on the left
side at the same time, then pull drawer out another inch.
4.
Holding the drawer by its sides, not its front, carefully pull it
all the way out.
To Replace:
1.
Align the drawer glides with the receiving guides.
2.
Push drawer in all the way.
3.
Gently open and close the drawer to ensure it is seated
properly on the slides.
TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the cost of
an unnecessary service call.
Nothing will operate
■
Is the power supply cord unplugged?
Plug into a grounded
3 prong outlet.
■
Has a household fuse been blown or has the circuit
breaker been tripped?
Replace the fuse or reset the circuit.
Surface burners will not operate
■
Is this the first time the surface burners have been used?
Turn on any one of the surface burner knobs to release air
from the gas lines.
■
Is the control knob set correctly?
Push in knob before
turning to a setting.
■
Are the burner ports clogged?
See “Surface Burners”
section.
Surface burner flames are uneven, yellow and/or noisy
■
Are the burner ports clogged?
See “Surface Burners”
section.
■
On models with caps, are the burner caps positioned
properly?
See “Surface Burners” section.
■
Is the burner damaged?
On models with caps, look for a
warped cap. If cap will not spin freely on a flat surface,
painted side down, the cap is warped. Switch cap with a
different surface burner to check for further warping. Contact
a service technician or see “Assistance or Service” section.
■
Is propane gas being used?
The appliance may have been
converted improperly. Contact a service technician or see
“Assistance or Service” section.
Surface burner makes popping noises
■
Is the burner wet?
Let it dry.
Excessive heat around cookware on cooktop
■
Is the cookware the proper size?
Use cookware about the
same size as the surface cooking area, element or surface
burner. Cookware should not extend more than 1 in. (2.5 cm)
outside the cooking area.
Cooktop cooking results not what expected
■
Is the proper cookware being used?
See “Cookware”
section.
■
Is the control knob set to the proper heat level?
See
“Cooktop Controls” section.
■
Is the appliance level?
Level the appliance. See the
Installation Instructions.
Oven will not operate
■
Is this the first time the oven has been used?
Turn any one
of the surface burner knobs on to release air from the gas
lines.
■
Is the electronic oven control set correctly?
See
“Electronic Oven Control” section.
Oven burner flames are yellow or noisy
■
Is propane gas being used?
The appliance may have been
converted improperly. Contact a service technician or see
“Assistance or Service” section.
Cooling fan runs during baking, broiling or cleaning
■
It is normal for the fan to automatically run while the oven is in
use to cool the electronic control.
Oven temperature too high or too low
■
Does the oven temperature calibration need adjustment?
See “Oven Temperature Control” section.
Display shows messages
■
Is the display showing “PF”?
There has been a power
failure. Clear the display. See “Display(s)” section. On some
models, reset the clock, if needed. See “Clock” section.
■
Is the display showing a letter followed by a number?
Depending on your model, press CANCEL, OFF or CANCEL/
OFF to clear the display. See “Display(s)” section. If it
reappears, call for service. See “Assistance or Service”
section.
Self-Cleaning cycle will not operate
■
Is the oven door open?
Close the oven door all the way.
■
Has the function been entered?
See “Self-Cleaning Cycle”
section.
■
On some models, has a delay start Self-Clean cycle been
set?
See “Self-Cleaning Cycle” section.
■
Has a delay start been set?
See “Timed Cooking” section.
