Whirlpool GBD279PVB Скачать руководство пользователя страница 4

4

 Cabinet Dimensions - Double Ovens

Double Ovens Installed in Cabinet

Cabinet Side View - Single or Double Oven 

Electrical Requirements

If codes permit and a separate ground wire is used, it is 
recommended that a qualified electrical installer determine that 
the ground path and the wire gauge are in accordance with local 
codes.
Check with a qualified electrical installer if you are not sure the 
oven is properly grounded.
This oven must be connected to a grounded metal, permanent 
wiring system.
Be sure that the electrical connection and wire size are adequate 
and in conformance with the National Electrical Code, ANSI/NFPA 
70-latest edition or CSA Standards C22.1-94, Canadian Electrical 
Code, Part 1 and C22.2 No. O-M91-latest edition, and all local 
codes and ordinances.

A copy of the above code standards can be obtained from:

 National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

Electrical Connection

To properly install your oven, you must determine the type of 
electrical connection you will be using and follow the instructions 
provided for it here.

Oven must be connected to the proper electrical voltage and 
frequency as specified on the model/serial number rating 
plate. The model/serial number rating plate is located at the 
bottom of the right-hand mounting rail. See the following 
illustrations.

 27" (68.6 cm) models

A. 27" (68.6 cm) min. cabinet 

width

B. 1" (2.5 cm) top of cutout to 

bottom of upper cabinet door

C. 14

³⁄₄

" (37.5 cm) bottom of 

cutout to floor

D. 25

¹⁄₂

" (64.8 cm)  cutout width

E. 1

¹⁄₂

" (3.8 cm) min. bottom of 

cutout to top of cabinet door

F. 49

³⁄₄

" (126.4 cm) min. cutout 

height

 30" (76.2 cm) models

A.

30

" (76.2 cm) min. cabinet 

width

B. 1" (2.5 cm) top of cutout to 

bottom of upper cabinet door

C. 14

³⁄₄

" (37.5 cm) bottom of 

cutout to floor

D. 28

¹⁄₂

" (72.4 cm) cutout width

E. 1

¹⁄₂

" (3.8 cm) min. bottom of 

cutout to top of cabinet door

F. 49

³⁄₄

" (126.4 cm) min. cutout 

height

A

B

C

D

E

F

A. 23

¹⁄₄

" (59.1 cm) min. cutout depth

B. 23" (58.4 cm) recessed oven depth

C. Oven front
D. Recessed oven

E. Cabinet

A

B

C

D

E

Single Oven
A. Model/serial number plate

Double Oven
A. Model/serial number plate

A

A

Содержание GBD279PVB

















Отзывы: