EN
User manual
7
CLEAN+
Clean+ is an option working on 3 different levels
(Intensive, Daily and Fast) that are specially designed to
set the right washing action, depending on your cleaning
needs:
Intensive :
this option is designed for high levels of
dirtiness, removing most stubborn stains .
Daily
:
this option is designed to remove everyday stains .
Fast :
this option is designed to remove lightly soiled
stains .
INTENSIVE RINSE
By selecting this option, the efficiency of the rinse is
increased and optimal detergent removal is guaranteed . It is
particularly useful for sensitive skin . Press the button once,
two or three times to select an additional 1
+1
, 2
+2
or 3
+3
rinses after the standard cycle rinse and remove all traces of
detergent . Press the button again to go back to the “Normal
rinse” rinse type .
START DELAY
To set the selected programme to start at a later time,
press the button to set the desired delay time . The symbol
lights on the display when this fuction is enabled . To
cancel the delayed start, press the button again untile the
value ‚‘‘0‘‘ is shown on the display .
ON/OFF
To switch on the washing machine: press the
“ON/OFF“ button, the “Start/Pause”
button light up .
To switch off the washing machine during the wash cycle,
press and hold the button for approximately 3 seconds . If
the button is pressed briefly or accidentally the machine will
not switch off .
To switch off the washing machine after programme end:
press the “ON/OFF“ button until the lights go off .
KNOB
To select and confirm programmes . Turn to
select .
START/PAUSE
To start the programme, after you have finished your
settings . To pause a running programme . To continue a
paused programme .
KEY LOCK
To lock the control panel, press and hold the
“Key lock”
button for approximately 3 seconds . The
symbol
will light up on the display to indicate that the
control panel has been locked (with the exception of the
“ON/OFF“ button) . This prevents unintentional changes
to programmes, especially with children near the machine .
To unlock the control panel, press and hold the “Key lock”
button for approximately 3 seconds .
FUNCTIONS
OPTIONS
BLEACHING
If you wish to bleach the laundry, load the washing machine
and set the “Rinse + Spin” programme
.
Start the machine and wait for it to complete the first water
filling cycle (roughly 2 minutes) . Put the machine in pause
mode by pressing the “Start/Pause”
button, open
the detergent drawer and pour the bleach (observe the
recommended doses indicated on the package) into the
main wash compartment where the partition was previously
mounted . Restart the cycle by pressing the “Start/Pause”
button .
If desired, it is possible to add fabric softener into the
appropriate compartment of the detergent drawer .
DEMO MODE
This function is only used for sales presentations . By this
you can interact with washing machine and see it working
without water . To enter Demo mode, switch the washing
machine ON and OFF again . Press and hold “Start/Pause”
button, then within 5 seconds press also “ON/OFF“
button and hold both buttons for 10 seconds .
To deactivate this function, switch the washing machine
OFF . Than press and hold “Start/Pause”
button, within
5 seconds press also “ON/OFF“ button and hold both
buttons for 2 seconds .
!
If the selected function is incompatible with the set programme, the incompatibility will be signalled by a buzzer (3 beeps) .
!
If the selected function is incompatible with another previously set function the function will not be enabled
.
FR
This option enhances washing performance by
generating steam to inhibit the proliferation of the main
bad odour sources inside the machine . After steam phase,
the washing machine will perform gentle tumbling through
slow rotations of the drum . Fr option starts after
the cycle ends for a maximum duration of 6h and you can
interrupt it at any time by pressing any button on control
panel or turning the knob . Wait around 5 minutes before
door can be opened .
TEMPERATURE
Every programme has a predefined temperature .
If you want to change the temperature, press the
“temperature” button . The value appears on the display .
SPIN
Every programme has a predefined spin speed . If you
want to change the spin speed, press the "Spin" button . The
value appears on the display .
