background image

21

Air Only

Use the Timed Dry/Air Only setting for items that require drying 
without heat such as rubber, plastic and heat-sensitive fabrics. 
This chart shows examples of items that can be dried using Air 
Only.

*Reset time to complete drying, if needed.

When using Air Only

Check that coverings are securely stitched.

Shake and fluff pillows by hand periodically during the cycle.

Dry item completely. Foam rubber pillows are slow to dry.

NOTE: Automatic Cycles are not available when using the Air 
Only setting.

Steam Cycles

In these cycles, a small amount of water is sprayed into the dryer 
drum after several minutes of tumbling with heat. The STEAM 
status light will come on while the water is sprayed into the drum. 
The dryer will continue to tumble at High heat for the duration of 
the cycle. The Steam cycles include Quick Refresh and 
Enhanced Touch Up. The heat setting and cycle time are not 
adjustable for the Quick Refresh cycle, but can be adjusted for 
the Enhanced Touch Up cycle.

NOTE: Results may vary depending on fabric. 100% cotton 
garments with wrinkle-free finish may yield better results than 
those without.

Use of a fabric softener sheet is not recommended with steam 
cycles as it may cause temporary staining on the clothes.

Quick Refresh

This cycle is best for smoothing out wrinkles and reducing odors 
from loads consisting of one to four dry items of wrinkle-free 
cotton, cotton-polyester blend, common knits and synthetic 
garments.

Enhanced Touch Up

This cycle uses water and heat to help smooth out wrinkles from 
items such as clothes packed in a suitcase or wrinkled from 
being left in the dryer too long.

*Temperature and time are selectable only for the Enhanced 

Touch Up Cycle.

NOTE: The Enhanced Touch Up cycle has a minimum dry time of 
15 minutes and a maximum dry time of 40 minutes. Only the 
Medium and High temperature settings can be used for the 
Enhanced Touch Up cycle.

Additional Features

Drum Light

Select Drum Light to turn on the light inside the dryer drum. 
During a cycle, if Drum Light is selected, the drum light turns on 
and will remain on until DRUM LIGHT is pressed again, the door 
is open and closed, or the door is left open for 20 minutes.

When the dryer is not running, the drum light will turn on when 
DRUM LIGHT is pressed or the dryer door is opened, and it will 
remain on until the dryer door has been open for 20 minutes, the 
dryer door is closed or DRUM LIGHT is pressed again. 

Press DRUM LIGHT at any time to turn the drum light ON or OFF.

WRINKLE SHIELD™ Feature 

When you are unable to remove a load of clothes from the dryer 
as soon as it stops, wrinkles can form. The WRINKLE SHIELD™ 
feature periodically tumbles, rearranges and fluffs the load to help 
keep wrinkles from forming.

Press the WRINKLE SHIELD™ feature to get up to 
140 minutes of heat-free, periodic tumbling at the end of a 
cycle.

Stop at any time by pressing the WRINKLE SHIELD™ feature 
or opening the dryer door.

For the Casual Cycle, the WRINKLE SHIELD™ feature is 
preset to “ON.” The other cycles will retain the WRINKLE 
SHIELD™ feature setting. (For example, if you select the 
WRINKLE SHIELD™ feature in the Normal cycle, the 
WRINKLE SHIELD™ feature will be on the next time you 
select the Normal cycle.)

NOTE: If you do not select the WRINKLE SHIELD™ feature, the 
dryer stops after the cool down period.

Damp Dry Signal

On some models, the Damp Dry Signal may be selected to alert 
you that your clothes are approximately 80% dry. This is useful 
when you want to remove lightweight items in a mixed load to 
avoid overdrying or remove partially dry items that may need 
ironing.

The DAMP DRY SIGNAL is useful when drying bedsheets/linens 
in a mixed load. When the signal goes off, open the door to stop 
the dryer, rearrange the load inside the dryer, close the door and 
restart the dryer to finish the drying cycle. Rearranging the load 
will aid in the drying process.

Press DAMP DRY SIGNAL until the desired volume (Loud, Soft or 
Off) glows green.

NOTE: The Damp Dry Signal is available only with the Automatic 
Cycles. The Damp Dry Signal is not a selectable option for the 
Sanitize cycle.

Type of Load

Time*
(Minutes)

Foam rubber - pillows, padded bras, stuffed toys

20 - 30

Plastic - Shower curtains, tablecloths

20 - 30

Rubber-backed rugs

40 - 50

Olefin, polypropylene, sheer nylon

10 - 20

Steam Preset Cycle Settings

Timed Cycles
Load Type

Default 
Temperature*

Default Time
(Minutes)*

QUICK REFRESH
Helps to smooth out 
wrinkles and reduce odors 
from loads consisting of 
one to four dry items.

Medium

15

ENHANCED TOUCH UP 
Helps to smooth out 
wrinkles in loads left in the 
dryer for an extended 
period.

Medium

20

Содержание Duet W10136968C





























Отзывы: