5019 301 15195
Whirlpool is a registered trademark of Whirlpool USA
Add the detergent as described in the programme
table or in the chapter “Detergent and Additives” of
the Instructions for Use.
1. Turn the programme selector to the desired
programme.
2. The remaining time display shows the duration
of the chosen programme (in hours and
minutes) and the lamp of the “Start/Pause”
button
flashes.
3. The indicator of the predefined spin speed
corresponding to the selected programme lights
up; it can be altered by pressing the “Variable
spin” button. The recommended temperature
(see indicator) can be altered by pressing the
“+” or “–” button.
Selecting any option the indication lights up.
When the combination of programme,
additional options and temperature is not
possible, the indication lights switch off
automatically and a signal sounds.
“Easy ironing” button
• Can be selected to reduce creasing.
• Increases the water quantity and the clothes are
spun very gently.
“Prewash” button
• Only for heavily soiled laundry (e.g. sand,
granular dirt). The cycle time increases by
approx. 15 minutes.
• Do not use liquid detergent for the main wash
when activating the “Prewash” button.
“Extra rinse” button
• More water and a longer time in rinse cycle is
added.
• This option is particularly suitable for areas with
very soft water, for baby clothes and to help
people with allergies.
“Rinse hold” button
• The laundry remains in the last rinse water
without being spun: this prevents creasing and
colours from changing.
• This option is particularly recommended for the
programme “Synthetics” or “Delicate”.
• It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain
only.
Note: The programme stops to “Rinse hold” as
soon as the “Rinse hold” light in the programme
sequence indicator lights up.
Terminate the “Rinse hold” option
:
• Press the “Rinse hold” button again; the
programme will terminate automatically with the
final spin cycle for the present wash programme.
CONSUMPTION DATA
Programme
Temperature
Selector
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approximate programme
duration*
(hours : minutes)
Cotton / Antibacterial
95
10.0
99**
3.15
2:45
Colours***
60
10.0
92
1.70
2:45
Colours
60
4.0
50
1.10
1:35
Colours
40
10.0
92
0.96
2:35
Synthetics
40
4.5
58
0.65
1:30
Daily load
40
4.5
58
0.65
1:00
Rapid plus
30
4.5
38
0.40
0:30
Delicate
30
3.0
70
0.45
0:50
Wool
40
2.0
60
0.50
0:35
Handwash
30
2.5
60
0.30
0:31
Big items
40
3.0
85
0.80
1:30
Prewash cycle increases programme duration by approximately 15 min. Consumption values were measured in normalized conditions in
compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the
water supply pressure and temperature, the load and the type of wash.
*
The remaining time indicator can deviate from the values in the table, because it takes into account the operating conditions
applicable at that time.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
*** Reference programme for energy label.
ADD DETERGENT, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
• If you do not wish to spin the clothes, press the
“Reset/Unlock door” button. The water is
drained out then, before the door can be opened.
“Variable spin” button
• Every programme has an automatic predefined
spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only.
The “Start delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is cheaper. Do not use liquid detergent
when activating the “Start delay”.
• Select programme, temperature and options.
• Press the “Start delay” button to select the delay
time by 1 to 23 hours;
• Press the “Start/Pause” button
.
• The time delay indication disappears when the
programme starts and it is replaced by the
remaining time.
• The number of hours preselected can later be
reduced pressing again the “Start delay” button.
To cancel the “Start delay”
.
• Turn the programme selector to the “
” position.
• Reselect the desired programme and options
and press the “Start/Pause” button
.
Turn on the tap and press the “Start/Pause”
button
. The pilot lamp of the “Start/Pause”
button
lights
up.
The indicator lamps show the sequence reached in
the programme. After starting the programme, the
sequence indication runs from top to bottom
through Prewash, Wash, Rinse, Spin.
When a sequence of the programme is finished the
corresponding lamp goes out.
Each time a programme starts the door is locked, the
“Door locked” indication light comes on and approx.
0.5 litres of water enters the machine. In the
programmes Cotton / Antibacterial, Colours,
Synthetics, Daily load and Rapid plus, for 10 minutes at
the beginning of the Main Wash the programme can be
interrupted by pressing the “Start/Pause” button
and the door can be opened again, e.g. to add more
washing. After this time, the door remains locked until
the end of the programme and must on no account be
forced open. You will find more information about
door locking in the Instructions for Use.
• The time remaining is “0:00” and the “End” light
is on.
1. Turn the programme selector knob to the “
”
position.
2. Turn the tap off and leave the door ajar to allow
the drum to dry.
1. Press the “Start/Pause” button
to
interrupt the programme. The light flashes.
2. Select the new programme (with temperature),
any options and another spin speed if you want.
3. Press the “Start/Pause” button
again. The
new programme continues at the same position
where the previous programme was interrupted.
Do not add detergent for this programme.
Press the “Reset/Unlock door” button
for at
least 3 seconds. Any existing water is drained out
before the door can be opened. Caution, the
washing could still be hot!
Detailed information can be found in the
instructions for use.
The controls can be locked to avoid interference by
children.
1. If the machine is off:
Turn the programme selector knob from the
OFF position “
” to any programme. Do not
press the “Start/Pause” button
. Press the
“Child lock” button for 5 seconds. The “Child
lock” indicator lights up. Turn the programme
selector knob to the OFF position “
” again.
2. While a programme is running:
Press the “Child lock” button
for 5
seconds. The child lock indicator will light up.
Now, in spite of the programme selector knob being
turned, no programme can be started or altered.
However, a running programme can be stopped at
any time (e.g. in an emergency), by turning the
programme selector knob to “
”. Attempts at
changing during the running programme are signalled
by the lamp of the accidentally chosen programme
flashing. The indicator light for the actual programme
running is on.
To unlock the controls, the machine must either have
a programme running or be in select mode. Press the
“Child lock” button
for 5 seconds. The child
lock lamp will go out.
START DELAY
PROGRAMME START
ADD WASHING/DOOR LOCK
PROGRAMME END
CHANGE THE PROGRAMME,
TEMPERATURE, OPTIONS AFTER
PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
CHILD LOCK
