background image

3

Installation must be carried out by a qualified electrician 

who is fully aware of current safety and installation 

regulations. The manufacturer declines all liability for injury 

to persons or animals and for damage to property resulting 

from failure to observe the regulations provided in this 

chapter.

Electrical connections

Hob electrical connection must be made before 

connecting the appliance to the electricity supply.

Electrical connection must be carried out in compliance 

with the regulations of the local electric utility company.

Make sure that the voltage indicated on the rating plate 

on the underside of the appliance corresponds to the 

domestic power supply voltage.

Regulations require that the appliance is earthed: use 

conductors (including the earth conductor) of the 

appropriate size only.

For electrical connection, use an H05 RR-F type cable as 

specified in the table “Power supply voltage”.

The 

power supply cable

 must be long enough 

to allow the hob to be removed from the 

worktop and must be positioned so as to avoid 

damage or overheating caused by contact with 

the base of the hob itself. 

Do not use extension leads.

Power supply voltage

If the hob already has a power cable, follow the 

instructions given on the label attached to the 

cable.

Connect the appliance to the electricity supply by 

means of an all-pole disconnect switch with minimum 

contact gap of 3 mm.

Connecting to the terminal board

Connect the yellow/green earth wire to the terminal with 
the symbol

. This wire must be longer than the other 

wires.

1.

Remove the terminal block cover (

A

), undoing the 

screw and inserting the cover in the terminal block 

hinge (

B

).

2.

Strip approx. 70 mm of sheath from the power supply 

cable. 

3.

Strip approx. 10 mm of sheath from the wires. Insert 

the power supply cable into the cable clamp and 

connect the wires to the terminal board as indicated in 

the diagram next to the terminal board itself.

4.

Secure the power cable with the cable clamp.

5.

Close the cover (

C

) and screw it on the terminal block 

with the removed screw - point (1).

Each time the cooktop is connected to the mains it 

carries out an automatic check which lasts several 

seconds.

INSTALLATION and ELECTRICAL CONNECTION

Wires

Amount x size

230V ~ + 

3 X 4 mm

2

230-240V ~ + 

3 X 4 mm

2

 (Australia only)

230V 3 ~ + 

4 X 1.5 mm

2

400V 3N ~ + 

5 X 1.5 mm

2

400V 2N ~ + 

4 x 1.5 mm

2

230V

230V

230V

230V

230V

230V

230V

230V

230V

230V

230V

A

B

C

400V 3N ~

230V ~

230-240V~FOR AU ONLY

230V~FOR UK ONLY

400V 2N ~

230V 3~

ONLY FOR BELGIUM

400V 2N~

FOR NL ONLY

Содержание ACM 702









Отзывы: