background image

10

Prepare Upper Cabinet

1. Disconnect power to outlet.
2. Remove all contents from upper cabinet.
3. Place Upper Cabinet Template against the bottom of the 

upper cabinet, and tape or tack it in place. Make sure the 
template centerline aligns with the vertical centerline on the 
rear wall.
The “rear wall” arrows must be against the rear wall so that the 
holes cut into the upper cabinet align with the holes in the top 
of the oven.

NOTE: If the upper cabinet has a frame around it, trim the 
template edges so that it fits inside the frame, against the upper 
cabinet bottom. The template has trim lines to use as guides.
4. Make sure the 10

¹⁄₂

" (26.7 cm) dimension from the rear wall to 

points “D” and “E” on the template is maintained.

5. Cut the 1

¹⁄₂

" (3.8 cm) diameter hole at the circular shaded area 

“G” on the template. This hole is for the power supply cord.

NOTE: If upper cabinet is metal, the supply cord bushing needs to 
be installed around the supply cord hole, as shown.

6. Drill 3/8" (10 mm) holes at points “D” and “E” on the template. 

These are for two 1/4-20 x 3" round-head bolts and washers 
used to secure the oven to the upper cabinet.

For Roof Venting Installation Only

7. Cut 3/4" (19 mm) hole at one corner of the shaded rectangular 

area “F” on Upper Cabinet Template.

8. Using a keyhole saw, cut out the rectangular area.

Install the Oven

IMPORTANT: The right side of the unit is the heavy side. Handle 
the oven gently.
1. Place a washer on each 1/4-20 x 3" flat-head bolt and place 

inside upper cabinet near the 3/8" (10 mm) holes.

2. Make sure the oven door is closed and taped shut.

3. Using 2 or more people, lift oven and hang it on support tabs 

at the bottom of mounting plate.

NOTE: Do not grip or use the door or door handle during 
installation.

A. Metal cabinet
B. Power supply cord bushing

D

E

G

Uppe

r-cabinet temp

l

at

e

F

10

¹⁄₂

"

(26.7 cm)

10

¹⁄₂

"

(26.7 cm)

A

B

A. Mounting plate
B. Support tabs

WARNING

Excessive Weight Hazard

Use two or more people to move and install 
microwave oven.

Failure to do so can result in back or other injury.

A

B

Содержание 8205272













Отзывы: