Whirlpool 5GR2SHKXLQ05, Инструкция по использованию и уходу

Страница: 12 / 40

12
4. Clean refrigerator, wipe it, and dry well.
5. Tape rubber or wood blocks to the tops of both doors to prop
them open far enough for air to get in. This stops odor and
mold from building up. Take care not to damage the door seal
with the blocks.
Moving
When you are moving your refrigerator to a new home, follow
these steps to prepare it for the move.
1. If your refrigerator has an automatic ice maker:
■
Turn off the water supply to the ice maker at least one day
ahead of time.
■
Disconnect the water line from the back of the refrigerator.
■
When the last load of ice drops, raise the wire shutoff arm
to the OFF (up) position.
2. Remove all food from the refrigerator and pack all frozen food
in dry ice.
3. Turn the Thermostat Control (or Refrigerator Control,
depending on the model) to OFF. See “Using the Controls.”
4. Unplug the refrigerator.
5. Empty water from the defrost pan located behind the base
grille.
6. Clean, wipe, and dry thoroughly.
7. Take out all removable parts, wrap them well, and tape them
together so they don’t shift and rattle during the move.
8. For models with leveling legs, adjust the rollers to raise the
front of the refrigerator so it rolls more easily. See “Adjust the
Doors.”
9. Tape the doors shut and tape the power cord to the
refrigerator cabinet.
When you get to your new home, put everything back
and refer to “Installation Instructions” for preparation instructions.
Also, if your refrigerator has an automatic ice maker, remember to
reconnect the water supply to the refrigerator.
TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.
Refrigerator Operation
The refrigerator will not operate
■
Power cord unplugged? Plug into a grounded 3 prong outlet.
■
Is outlet working? Plug in a lamp to see if the outlet is
working.
■
Household fuse blown or circuit breaker tripped? Replace
the fuse or reset the circuit breaker. If the problem continues,
call an electrician.
■
Control(s) on? Make sure the refrigerator controls are on. See
“Using the Control(s).”
■
New installation? Allow 24 hours following installation for the
refrigerator to cool completely.
NOTE: Adjusting the temperature controls to coldest setting
will not cool either compartment more quickly.
The motor seems to run too much
Your new refrigerator may run longer than your old one due to its
high-efficiency compressor and fans. The unit may run even
longer if the room is warm, a large food load is added, doors are
opened often, or if the doors have been left open.
The refrigerator seems noisy
Refrigerator noise has been reduced over the years. Due to this
reduction, you may hear intermittent noises from your new
refrigerator that you did not notice from your old model. Below are
listed some normal sounds with explanations.
■
Buzzing - heard when the water valve opens to fill the ice
maker.
■
Pulsating - fans/compressor adjusting to optimize
performance.
■
Hissing/Rattling - flow of refrigerant, movement of water
lines, or from items placed on top of the refrigerator.
■
Sizzling/Gurgling - water dripping on the heater during
defrost cycle.
■
Popping - contraction/expansion of inside walls, especially
during initial cool-down.
■
Water running - may be heard when water melts during the
defrost cycle and runs into the drain pan.
■
Creaking/Cracking - occurs as ice is being ejected from the
ice maker mold.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING