Whipple EB-8185 Скачать руководство пользователя страница 16

Страница: 16 / 16

Instruction Manual: Bronco_Megacooler_8185_R1

Last Updated: April 28

, 2022

Page 16 of 16

www.whipplesuperchargers.com

37.

NOTE:

Measurement must be taken from the non-raised side of the CCM. Keeping the combination square level on

the face of the CCM, adjust the pitch by turning the adjustment screw until the CCM is vertical and level.

38.

NOTE:

The horizontal alignment for the CCM (cruise control module) is a software calibration check that is

performed by the scan tool to insure the CCM (cruise control module) radar is pointed straight. No manual

adjustment is needed for this procedure. The scan tool calibrates the CCM (cruise control module) through the

CCM (cruise control module) procedure in programmable parameters. The Alignment Offset specification is +/- 3.0

degrees of offset.

NOTICE: The vehicle's engine must be running during the horizontal alignment

procedure. Failure to leave the engine running throughout the entire procedure results in the

cancellation of the alignment procedure and the system remains non-functional.

39.

Follow the scan tool on-screen instructions to carry-out the CCM calibration procedure.

Содержание EB-8185

















Результаты поиска

Содержание EB-8185

Отзывы:

Похожие инструкции для EB-8185

Бренды по названию

Популярные бренды

Whipple EB-8185, Инструкция по эксплуатации

Результаты поиска

Содержание EB-8185

Отзывы:

Похожие инструкции для EB-8185

Бренды по названию

Популярные бренды