Page 4
BROWN
WHITE
BROWN
WHITE
BROWN
WHITE
BROWN
WHITE
CometFlash®
SingleFlash
DoubleFlash
ActionFlash™
BATTERY
S360D Disassembly Procedure:
1.
Remove the clamp ring screw and the clamp ring (Fig. 7).
2.
Carefully remove the optic dome, the inner optic lens and
upper reflector.
3.
Lift off the strobe tube assembly, unplug it and put it
aside.
4.
Remove the 3 screws holding the circuit board to the
base casting, and lift the circuit board off.
IMPORTANT:
Always be sure to tape or remove any unused
wires.
S360D Assembly Procedure:
1.
Feed the wires out through the wire slot in the strobe
power supply assembly and attach the power supply
assembly to the aluminum base using the 3 power supply
screws and lockwashers.
IMPORTANT:
Be sure the alignment tab in the aluminum base
lines up with the wire slot in the strobe power assembly (Fig. 3).
2.
Connect the wires and place the strobe bulb assembly on
top of the base (be careful to line the wide notch in the
strobe bulb assembly up with the wire slot in the strobe
power supply assembly as shown in Figure 3).
3.
Place the inner optic lens on top of the strobe and the upper
reflector on top of the optic lens.
4.
Attach the optic dome to the base with the clamp ring and
screw.
Note: Be sure to position the clamp ring with the
screw facing the rear of the vehicle.
BLACK WIRE, NEGATIVE (-)
RED WIRE, POSITIVE (+)
ON/OFF SWITCH
FUSE
WIRES TO POWER SOURCE
WIRES TO STROBE
LIGHT HEAD ASSEMBLY
DOUBLE POLE, DOUBLE THROW
CENTER OFF SWITCH (REAR VIEW)
BLACK WIRE, NEGATIVE (-)
RED WIRE, POSITIVE (+)
RED WIRE, POSITIVE (+)
BLACK WIRE, NEGATIVE (-)
VIOLET WIRE, NEGATIVE (-) HI/LOW
WIRES TO POWER SOURCE
WIRES TO STROBE
LIGHT HEAD ASSEMBLY
FUSE
GRAY WIRE, POSITIVE (+) CRUISE LIGHT, 12 OR 24 VDC
DOUBLE POLE, DOUBLE THROW
CENTER OFF SWITCH (REAR VIEW)
BLACK WIRE, NEG. (-)
RED WIRE, POS. (+)
RED WIRE, POSITIVE (+)
BLACK WIRE, NEGATIVE (-)
VIOLET WIRE, NEGATIVE (-) HI/LOW
WIRES TO POWER SOURCE
WIRES TO STROBE
LIGHT HEAD ASSEMBLY
FUSE
GRAY WIRE, POSITIVE (+) CRUISE LIGHT, 12 OR 24 VDC
1 AMP FUSE
MODEL S360D STANDARD.
ON/OFF SWITCHING
FOR HIGH POWER
ONLY.
MODEL S360D STANDARD.
HIGH-OFF-LOW SWITCHING.
NOTE: Cut Violet (looped) wire,
run it out of unit with black and
red wires. When the violet wire
is grounded, you are in high
mode and when the violet wire
is floating you are in low mode.
IMPORTANT: Cruise light
is 12 VDC or 24 VDC bulb.
MODEL S360D WITH CRUISE
LIGHT OPTION.
NOTE: Strobe light and cruise
light are connected to same
DPDT CENTER OFF switch
control.
MODEL S360D WITH CRUISE
LIGHT OPTION.
IMPORTANT: Cruise light
is 12 VDC or 24 VDC bulb.
NOTE: Strobe light is controlled
by DPDT CENTER OFF switch
control, and cruise light is
controlled by ON/OFF
switch control.
NOTES:
10 AMP
5 AMP
24 VDC
ALL SWITCHES AND FUSES ARE CUSTOMER SUPPLIED. USE
FUSE FOR 12 VDC
OPERATION, AND
FUSE FOR
OPERATION.
SWITCH CONTROL WIRING SCHEMATICS FOR THE S360D STROBE LIGHT SERIES
+
+
BLACK WIRE, NEGATIVE (-)
RED WIRE, POSITIVE (+)
RED WIRE, POSITIVE (+)
BLACK WIRE, NEGATIVE (-)
VIOLET WIRE, NEGATIVE (-) HI/LOW
WIRES TO POWER SOURCE
WIRES TO STROBE
LIGHT HEAD ASSEMBLY
FUSE
DOUBLE POLE, DOUBLE THROW
CENTER OFF SWITCH (REAR VIEW)
+
+
Fig. 4
WHELE
N ENG
.
8 1642
STROBE BULB ASSEMBLY
82773
DIE CAST BASE
STROBE POWER SUPPLY ASSEMBLY
ALIGNMENT TAB
WIRE SLOT
WIDE NOTCH
NOTE POSITION
OF HOLES
NOTE POSITION
OF SCREWS
ALI
G
NMENT TA
B
Fig. 3
