Page 2
This ISP9424A Intelligent Strobe Power Supply (hereafter
collectively refered to as “ISP”) can be installed in many different
types of vehicles. The guidelines for the installation of this product
are written so that no matter what vehicle is being used, the
installation and operation of the ISP will be simple and straight
forward.
Section 1: Selecting a mounting location
A good choice for a mounting area would be a trunk or similar
compartment. However, due to the wide variety of vehicles onto
which the ISP can be installed, this is not always possible. The
following guidelines will help the installer select an acceptable
alternative:
•
The ISP should be mounted on a metal surface to aid
heat dissipation. Be sure that this surface is not one that
either generates or is exposed to excessive heat during
normal operation of the vehicle.
•
Do not select a location where the ISP will be exposed to
potential damage from any unsecured or loose
equipment in the vehicle.
•
Be sure the area selected will not allow the ISP to be
exposed to water.
•
When routing wires, it is important to choose a path that
will keep them away from excessive heat and from any
vehicle equipment that could compromise their integrity
(ex. trunk lids, door jams, etc.).
•
Be sure your mounting location does not block the
cooling fan in the rear of the unit. (Fig. 1)
•
When the best mounting location has been determined,
securely fasten the ISP to its mounting surface using the
supplied hardware.
IMPORTANT! All customer supplied wires, that connect to
the positive (+) terminal of the battery, must be sized to
supply at least 125% of the maximum operating current, and
fused “at the battery” to carry the load.
WARNING!
When extending the communication wires
(BLUE & GREY), use either the Whelen 25ft cable (P/N 46-
9641638250) or similar “twisted pair” wires.
Caution: As it will be necessary to drill holes into the
mounting surface, the installer MUST be sure that no
vehicle components or other vital parts could be
damaged by the drilling process. Check both sides of
the mounting surface before drilling begins.
Section 2: Operating Instructions:
The ISP has been designed to emulate the operations of four
different types of power supplies:
Alternating Outlets
. . . . . . . . . . . . . . . . . . . . . Alt. 2X2
Simultaneous Outlets (by pairs)
. . . . . . . .Simul. 2X2
Simultaneous Outlets
. . . . . . . . . . . . . Simul. 2X1X1
S.C. (Serial Communication)
. . . . . . . . . . . . . Custom
Select the desired operational mode by configuring dip switches
1, 2 & 5, located on the front panel of the power supply. The use of
dip switches 3 & 4 is explained in the “Hi-Lo Power” section.
The following will explain how to place the ISP into each of these
respective modes, as well as outline the operational procedures
for each mode.
Emulation Modes
Mode 1: Alternating Outlets (default configuration)
Dip Switches
Dip Switch configuration for Alternating Outlet-mode:
Dip Switch 1
-
OFF
Dip Switch 2 -
OFF
Dip Switch 5 -
OFF
Control Wires
In this configuration, ap24VDC to the control wires (using
customer supplied switches) will have the following results:
Control Wire #1 =
Outlets 1 & 2 enabled
Control Wire #2 =
Outlets 3 & 4 enabled
Control Wire #3 =
All Outlets enabled
Control Wire #4 =
See Section 3: Hi/Lo Power)
Flash Patterns:
See Section 4.
Mode 2: Simultaneous Outlet Mode
Dip Switches
Dip Switch configuration for Simultaneous Outlet-mode:
Dip Switch 1 -
ON
Dip Switch 2 -
OFF
Dip Switch 5 -
OFF
Control Wires
In this configuration, ap24VDC to the control wires (using
customer supplied switches) will have the following results:
Control Wire #1 =
Outlets 1 & 3 enabled
Control Wire #2 =
Outlets 2 & 4 enabled
Control Wire #3 =
All Outlets enabled
Control Wire #4 =
See Section 3: Hi/Lo Power
Flash Patterns:
See Section 4.
