Page 3
10
11 12
14
13
1
2
3
6
4
5
7
9
8
RED (+)
BLACK (-)
DESC
RIP
T
I
ON
F
L
AN
G
E
M
O
U
NT
M
A
G
NET
I
C
M
O
U
NT
R
E
GUL
A
R
M
O
U
NT
I
TE
M
Q
T
Y.
DECAL
LAMP HOLDER ASSY.
SEAL
P.C. BOARD ASSY.
P
A
R
T N
UM
BE
R
38-0141350-00
02-0341319-00
38-0241323-00
02-0166934-00
1
1
1
1
1
8
9
10
BASE, HOUSING
BASE, HOUSING
11-362261-000
11-361303-000
1
1
11
12
GASKET
38-0242108-00
1
13
GASKET
38-0241351-00
1
14
KIT, SCREW MOUNT
01-0416225-00
Not
Shown
-
1” x 2” HOOK & LOOP
01-0416225-00
Not
Shown
-
LENS (RED)
LENS (GREEN)
LENS (CLEAR)
LENS (BLUE)
LENS (AMBER)
68-2181382-50
68-2181382-40
68-2181382-30
68-2181382-20
68-2181382-10
A/R
A/R
A/R
A/R
A/R
6
5
4
3
2
LENS SHIELD COVER
11-261332-000
A/R
7
Flash Tube
Replacement:
WARNING!
WAIT 10
MINUTES
after turning power
off before starting any work or
troubleshooting.
A.
Remove the optic dome as
outlined on the previous
page.
B.
Pinch together the mount-
ing prongs on the lamp holder
assembly and lift it free from
the power supply assembly.
C.
When replacing the strobe
lamp assembly, note that it
can be installed one way only. Align the three metal leads and
the index pin. Push the assembly into the power supply
assembly until the assembly’s mounting prongs snap into
position.
D.
Replace the optic dome by aligning the tabs on the dome
with the pockets in the strobe light base. Make sure the dome
gasket is in place. Press firmly on the dome to engage the
retainer clips located inside the pockets.
WIRING INSTRUCTIONS:
NOTE:
DC voltage models are polarity sensitive. If the positive
and negative wires are reversed the unit will not function. A 2 amp
fuse (customer supplied) must be installed in the RED (+) wire
within 2 wire feet of the power source.
1.
Connect RED wire on beacon to positive (+) DC voltage .
2.
A customer supplied single pole single throw (SPST) switch
may be used to control the ON-OFF function of the beacon.
3.
Connect BLACK wire on the beacon to negative (-) ground.
WARNING:
All customer supplied wires, that connect to the
positive terminal of the battery, must be sized to supply at least
125% of the maximum operating current, and fused at the
battery to carry that load.
Trouble Shooting:
WARNING!
The strobe light is a high voltage device.
DO NOT
TOUCH
the strobe lamp assembly or the strobe power supply
assembly while the unit is in operation!
WAIT 10 MINUTES
after
turning power off before starting work or troubleshooting.
Light does not work after initial installation:
1.
Check wires for proper hook-up.
2.
Check power source.
3.
Check any in-line fuses or switches.
4.
Check that the strobe lamp assembly is firmly secured to the
power supply assembly.
Strobe light fails or becomes intermittent during service:
1.
Check power source.
2.
Check any in-line fuses or switches.
3.
Check power wires for breaks, chafing, or loose connections.
4.
Check that the strobe lamp assembly is firmly secured to the
strobe power supply assembly.
5.
A strobe flash tube that is 50% black, is at the end of its service
life and should be replaced.
6.
A strobe flash tube can become hard firing with age. It will
sometimes flash normally with the engine running, but will fail
when operated on a low battery. If so, it should be replaced.
The outer surfaces of this product may be cleaned with
mild soap & water. Use of other chemicals may void
product warranty. Do not use a pressure washer.
Fig. 2
Mounting
Prong
Base
Power
Supply
Assembly
Metal
leads
Strobe
Lamp
Holder
