3
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service (800) 793-7846
www.westinautomotive.com
P.N.: 75-0026-RevF
ECO #: W17-0060
DATE: 6/21/17
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
4. Select the correct driver side Inner Support Bracket for your application.
For 2WD vehicles or 4WD without optional factory transfer case skid plate:
Locate the oval hole in the bottom of the
frame channel. Insert (1) M10 short bolt plate into the hole and rotate it 90-degrees. See
Figures 5A & 5B
. Select the
Driver Side Front Inner Support Bracket. Bolt the Bracket to the previously installed Bolt Plate with (1) M10 flat washer,
(1) M10 lock washer and (1) M10 hex nut. See
Figure 6.
Line up the remaining hole in the Support Bracket with the hole
in the center of the Front Mounting Bracket.
Note:
Flange of inner support bracket attaches on the outside for passenger
side only. (
Figure 14
) Bolt the two Brackets together with (1) M12 hex bolt, (2) M12 large flat washers, (1) M12 lock
washer and (1) M12 hex nut. See
Figure 6.
Line up the hole in the Outer Support Bracket with the hole in the Front
Mounting Bracket.
Note:
The Outer Support Bracket will line up on the forward facing side of the Mounting Bracket. Bolt
the two Brackets together with (1) M10 x 30mm hex bolt, (2) M10 flat washers and (1) M10 nylon lock nut. See
Figures
5A & 6.
Do not tighten.
Figure 3
Front
Figure 4
4.
For 4WD vehicles with optional transfer case skid plate:
Step below applies to driver side Inner Support Bracket instal-
lation only. Use Step above for passenger side Inner Support Bracket installation. On the driver side, locate the hex bolt
securing the rear of the skid plate to the bottom of the frame channel. See
Figure 7A.
Remove the factory hex bolt. Select
the Driver Side Front Inner Support Bracket for models W/Factory Skid Plate. See
Figure 7B.
Place the Bracket over the
skid plate and bolt it in place with (1) M10 x 40mm hex bolt, (1) M10 flat washer and (1) M10 lock washer. Leave hard-
ware loose at this time. Line up the (2) holes in the outer end of the Support Bracket with the holes in the Front Mounting
Bracket. Line up the hole in the Outer Support Bracket with the hole in the Mounting Bracket and Support Bracket. See
Figure 7A. Note:
The Outer Support Bracket will line up on the rear facing side of the Mounting Bracket. See
Figure 7B.
Bolt the (3) Brackets together with (2) M10 x 35mm hex bolts, (4) M10 flat washers and (2) M10 nylon lock nuts. Do not
tighten hardware at this time.
Note:
Follow step above for passenger side Inner Support Bracket installation instructions for all vehicles.
5. Move to the driver side rear of the vehicle and remove the rubber plug or sticker in the bottom of the rocker panel as de-
scribed in
Step 2
. Insert (1) M12 bolt plate into the oval hole and rotate 90-degrees to the slot. See
Figure 8.
Select (1)
Driver Side Outer Support Bracket and secure it to the Bolt Plate with (1) M12 lock washer, (1) M12 small flat washer and
(1) M12 hex nut. Locate the oval hole in the floor panel on the other side of the pinch weld, forward of this location. Insert
(1) M10 large bolt plate into the hole and rotate 90-degrees to the oval hole. See
Figures 9A & 9B.
Figure 5A
Figure 5B
Figure 6
Driver side front support bracket for
vehicles without Skid Plate Shown
Flange of support bracket attaches on
the outside. Refer to Figure 14.
