Western Telematic MDS-16 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 58

background image

4.

Hardware Installation

This section describes the procedures for installing the MDS and

connecting devices to the unit.

4.1.

Configure Setup Switches

When the MDS is shipped from the factory, the Setup Switches

are configured for 9600 baud, 8 Bits-No Parity, DTR

handshaking, verbose command response, and no echo (all

switches down). These switch settings are compatible with most

applications. If the default settings are

not

compatible with your

application, change the switch settings as described in the

following subsections.

Setup Switches should be configured to match the

communication parameters used by the device attached to Port 1.

This allows access to the MDS if the unit is initialized to default

parameters.

Note:

Communication parameters (baud rate, parity, etc.)

can also be individually selected for each MDS port

by accessing the Command Mode and invoking the /P

command as described in Section 5.3.4. However, if

the MDS is initialized, parameters will return to the

settings specified by the current Set-Up Switch

configuration.

4-1

«
...
13
14
15
16
17
...
»

Содержание MDS-16



























































Отзывы:

Нет отзывов

Похожие инструкции для MDS-16

Бренд: ABB Страницы: 32

Бренд: ABB Страницы: 44

Бренд: ABB Страницы: 15

Switch 4500 Family

Бренд: 3Com Страницы: 16

PathBuilder S200 Series

Бренд: 3Com Страницы: 32

Бренд: GarrettCom Страницы: 24

Бренд: Siqura Страницы: 2

Бренд: Labgear Страницы: 4

ALTUSCN KH1508I

Бренд: ATEN Страницы: 173

Бренд: Key Digital Страницы: 20

Бренд: Cabletron Systems Страницы: 83

Бренд: CableTronix Страницы: 4

Бренд: Videplus Страницы: 13

Бренд: Comprehensive Страницы: 12

R-TEC Automation RTMWSR15C

Бренд: Rowley Страницы: 10

Бренд: Black Box Страницы: 76

Бренд: Smartwares Страницы: 2

Бренд: Videosec Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды