Westermo SDW-500 Скачать руководство пользователя страница 20

Страница: 20 / 22

6644-2214

DIP switch settings SDW-541 and SDW-532

DIP-switches are accessible under the lid on top of the product. DIP-switches are used
to configure the product.

NOTE

When configuration via DIP-switches, the settings of DIP-switches configure the product
only after a reboot (power off/on).

Observe this when the DIP-switches are configured:

… Speed and duplex setting only valid when auto-negotiation is disabled.
… When monitoring selected all outgoing packets from the switch is also copied to the

port 1.

… Speed and duplex switch settings are ignored for FX ports.
… If auto-negotiation and auto MDI/MDI-X disabled all TX ports support MDI-X

configuration.

CAUTION - ELECTROSTATIC DISCHARGE (ESD)

Prevent electrostatic discharge damages to internal electronic
parts by discharging your body to a grounding point (e.g. use a
wrist strap).

WARNING - HAZARDOUS VOLTAGE

Do not open an energized product. Hazardous voltage may occur
when connected to a power supply.

Содержание SDW-500























Результаты поиска

Содержание SDW-500

Отзывы:

Бренды по названию

Популярные бренды

Westermo SDW-500, Руководство пользователя

Результаты поиска

Содержание SDW-500

Отзывы:

Бренды по названию

Популярные бренды