Westermo SDW-500 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 22

Westermo SDW-500 Скачать руководство пользователя страница 16

16

6644-2214

Installation

Mounting / Removal

Mounting

This product should be mounted on
35 mm DIN-rail which is horizontally
mounted on a wall or cabinet
backplate.

CLICK!

CLICK!

CAUTION - ELECTROSTATIC DISCHARGE (ESD)

Prevent electrostatic discharge damages to internal electronic
parts by discharging your body to a grounding point (e.g. use a
wrist strap).

WARNING - HAZARDOUS VOLTAGE

Do not open an energized product. Hazardous voltage may occur
when connected to a power supply.

Cooling

This product uses convection cooling.
To avoid obstructing the airflow around the
product, use the following spacing rules.
Minimum spacing 25 mm (1.0 inch) above /
below and 10 mm (0.4 inches) left / right the
product.
Spacing is recommended for the use of prod-
uct in full operating temperature range and
service life.

10 mm *

(0.4 inches)

25 mm

25 mm

* Spacing (left/right) recommended for

full operating temperature range

Removal

Press down the black support at the back of the product,

see figure.

«
...
14
15
16
17
18
...
»

Содержание SDW-500























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды