Westermo GD-01 TCP Скачать руководство пользователя

Страница: 116 / 206

116

6196-2220

+ICF – DTE-DCE character framing

Description:

This command is used to determine the local serial port start-stop (asynchronous)
character framing that the DCE uses.

Syntax:

AT+ICF= <format>, <parity>

Command example

Possible responses

Note

AT+ICF? +ICF: 3,4

Current

values

AT+ICF=? +ICF: (1-6),(0-4)

Possible

values

AT+IPR=38400

Disable autobauding and
set rate to 38400 bps

AT+ICF=0,0 OK

New

values

Defined values:

<format>

Autodetect (not supported)

8 Data 2 Stop (supported)

8 Data 1 Parity 1 Stop (supported)

8 Data 1 Stop (supported)

7 Data 2 Stop (supported)

7 Data 1 Parity 1 Stop (supported)

7 Data 1 Stop (supported)

<parity>

Odd (supported)

Even (supported)

Mark (supported)

Space (supported)

None (supported)

NOTE 1:

setting a character framing different from 8N1 will disable autobauding
(in the case it was activated). However setting it back to 8N1 will not
re-enable autobaud.

NOTE 2:

setting the framing to 8N1 will let the autobauding enabled, if it was already

enabled (implying framing was already 8N1).

Содержание GD-01 TCP















































































































































































































Результаты поиска

Содержание GD-01 TCP

Отзывы:

Похожие инструкции для GD-01 TCP

Бренды по названию

Популярные бренды

Westermo GD-01 TCP, Инструкция по интерфейсу

Результаты поиска

Содержание GD-01 TCP

Отзывы:

Похожие инструкции для GD-01 TCP

Бренды по названию

Популярные бренды