Westell AISG-RM3 Скачать руководство пользователя страница 7

Section AIS‐RM3‐20B

030‐101806 Rev. A

R

1310IBRA

7

Field Name

Description / Options

IP Address

Change to the new IP address assigned to the AISG‐RM3
controller at the site network.

SubNetwork
Mask

Change to the new SubNetwork Mask used at the site net­
work.

Gateway IP

Change to the new Gateway IP used at the site network.

Table 5.    Network Settings / IP Address Fields

Click on the Save button in the upper right corner once you have
finished changing the values. An alert window appears.

Click on the OK button to confirm the save.

After saving, the new settings will only take effect after the sys­
tem is rebooted. Click the Reboot button to reboot the system.

Click OK to confirm and initiate the reboot process.

Wait for the process to end. You may need to reconnect to the
AISG‐RM3 using the new IP if the IP is changed.

4.1.2

System Information and Language

The 

System Information

 section (see Figure 12 or Figure 14)

shows the Product Model, Serial No., Hardware Version and
Software Version of the AISG‐RM3 system. The desired user in­
terface language can also be changed here. Select the preferred
language from the drop­down list and click the Set button to ap­
ply the change.

Figure 14. System Information Area

4.1.3

Power Setting

In the 

Power Setting

 section (Figure 15), the power voltage and

power supply mode provided to the connected AISG devices can
be changed. Change the settings  per company practice, refer­

ring to Table 6 as needed, then click on the Set button to apply
the changes.

Figure 15. Power Setting Area

Field Name

Description / Options

Power Supply

DC 12V or DC 24V. Check to select the proper voltage.

Power Mode:
Always On

Check to supply power continuously.

Power Mode:
Power Save

This is a power saving mode. Check to supply power only
when a command is initiated; otherwise power is not sup­
plied.

Table 6.    Power Setting Fields

When the Set Power process is completed, the following pop­up
window is displayed. Click on the Close button to close it.

4.1.4

Device Setting

In the 

Device Setting

 section, select the Scan Length value used

when scanning for devices. The default value is 4. This value can
be increased if a connected device is not being distinguished
from another during a scan.

Figure 16. Device Setting Area - Scan Length

Click on the Set button to apply the changes. Click on the Close
button when the process is finished.

4.1.5

System Time Setting

The 

System Time Setting 

section is used to set the system date

and time. The date uses the mm/dd/yyyy format. By clicking on
the Select Date button, a calendar pop­up appears which can be
used to select the date. The time setting uses the 24­hour format.

Figure 17. System Time Setting Area - Date Format

Click on the Set button to apply the changes. Click on the Close
button when the process is done.

Содержание AISG-RM3























Отзывы: