Westco 16-25 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 49

Westco 16-25 Скачать руководство пользователя страница 3

Section 5

Section 6

Section 7

Section 8

Contents

(continued)

Troubleshooting, Repair and Overhaul

Troubleshooting
Repair
Overhaul

Testing

Test Recommendations
Free Run Test
Torque-Up Test

Jaw Installation and Parts

Installation
Jaw Roller Size Check

Tong Assembly, Disassembly and Parts

Disassembly
Rotary Assembly
Parts List for Rotary Assembly
Parts List for Case/Door Assembly
Installation Drawing, Case/Door Assembly
Parts List for Case/Door Assembly

(For Tongs with Half Rollers)

Installation Drawing, Case/Door Assembly

(For Tongs with Half Rollers)

Parts List for Gear Box Assembly
Installation Drawing, Gear Box Assembly
Parts List for Motor Assembly
Installation Drawing, Motor
Parts List for Manifold Assembly
Installation Drawing, Manifold
Parts List for Manifold Assembly

(For Tongs with Tandem Motors)

Installation Drawing, Manifold

(For Tongs with Tandem Motors)

Page

5.1

5.1

5.1

5.3

6.1

6.1
6.1
6.1

7.1

7.1

7.1

8.1

8.1

8.1

8.4

8.5

8.6

8.7

8.8

8.9

8.10

8.11
8.11

8.12

8.13

8.14

8.15

«
1
2
3
4
5
...
»

Содержание 16-25


















































Отзывы:

Нет отзывов