Westco 16-25 Скачать руководство пользователя страница 17

Section 3 Page 4 

 

Section 4 

 

Maintenance  

Servicing the tong consists of inspection, lubrication, tests and adjustments. Should 

 

servicing reveal requirements for repairs, refer to the appropriate procedures in 

 

"Troubleshooting, Repair and Overhaul" and "Testing" (Sections 5 and 6).  

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Overhaul Equipment 

 

 

 
 

Jaw Dies 

 

 

 

Rotary Gear 

 

 

 
 

Latch Hook Springs 

 

 

 

Jaw Rollers  

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Daily Inspection 

 

Figure 4-1 illustrates the points that should be inspected prior to every job and 

 

once every operating day thereafter. 

 

Inspect the unit and its accessories for obvious damage, evidence of hydraulic 

 

leaks, etc. Refer to the overhaul procedures for removal and replacement of 

 

any faulty parts. 

 

Inspect jaw dies to be sure that the biting edge is not worn excessively and is 

 

capable of biting effectively. Change the dies if necessary. 

 

Inspect gear teeth for excessive wear, damage or breakage. Replace if more 

 

than two adjacent teeth are broken. If excessive wear or breakage is found, 

 

inspect all internal gears and grease packing for metal particles and damage. 

 

Springs must exert sufficient force to close latch firmly on the lug. Replace 

 

if necessary. 

 

Inspect jaw roller for free rotation. Lubricate as described under Jaw Roller 

 

Lubrication procedure.  

Содержание 16-25


















































Отзывы: