Wessex CRX-410 Скачать руководство пользователя страница 12

Страница: 12 / 43

WINTER STORAGE

Before winter storage, the CRX Tri-deck should be thoroughly inspected:-

Repair or replace any worn or broken parts.

Check oil level in the gearbox. Top up or change with EP90 gear oil.

Take special care to look at the blades, rotor and the bearings.

Remove the belts and ensure that the rotors are free-spinning.

Make sure that the belts are in good condition before re-fitting.

Thoroughly wash the machine to remove all oil, grease, debris and materials.

Grease all grease points before storage to avoid any corrosion.

After pressure washing always run mower for a time to expel any water from bearings.

It is recommended to apply a light oil to the under-deck surfaces to protect the machine from
corrosion while in storage.

TROUBLESHOOTING

FAULT

CAUSE

REMEDY

Leaving wheel track uncut

1. Forward speed too fast

2. Cutting height too high

3. Excessive blade wear

Reduce forward speed

Lower cutting height

Replace blades

Bad quality of cut

1. Forward speed too fast

2. Excessive blade wear

3. Belts slipping

Reduce forward speed

Replace blades

Tighten belts

Narrow strip uncut

1. Possibly missing or broken

blade

Inspect blades and replace as

necessary

Excessive vibration

1. Damaged or missing blades

2. Main spindle bearing play

3. Loose part

Inspect and replace blades

Inspect bearing, replace if damaged

Check all nuts and bolts are tight

Excessive scalping

1. Cutting height too low

Raise cutting height.

Содержание CRX-410












































Результаты поиска

Содержание CRX-410

Отзывы:

Похожие инструкции для CRX-410

Бренды по названию

Популярные бренды

Wessex CRX-410, Руководство по эксплуатации и каталог запасных частей

Результаты поиска

Содержание CRX-410

Отзывы:

Похожие инструкции для CRX-410

Бренды по названию

Популярные бренды