Wesco CBV36WT, Оригинальное руководство пользователя, Страница: 10 / 48

10
EN
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the instruction
book carefully.
Intended use
The blower is intended for blow debris. It’s not intended for
use indoors and animal grooming.
ASSEMBLY
1. ASSEMBLING AND DISASSEMBLING THE BLOWER
TUBE
- ASSEMBLING (SEE FIG. A1)
Before assembling the blower tube, be sure the battery is
not installed.
To assemble, press the tube release button and slide
the upper blower tube to the motor housing. Ensure the
hole on the upper blower tube matches up with the tube
release button on the motor housing. Slide the lower
blower tube to upper blower tube. Ensure the hole on the
lower blower tube matches up with the raised block on the
upper blower tube. Pull the lower blower tube to check if it
is assembled well.
- DISASSEMBLING (SEE FIG. A2)
Before disassembling the blower tube, be sure the battery
is not installed.
To disassmble, press the tube release button, and remove
the upper tube from the motor housing.
BEFORE OPERATION
1. CHARGING THE BATTERY PACK
a)Do not use any charger other than that specifically
provided for use with the equipment.
b) If the battery pack is very hot you must remove your
battery pack from the charger and allow time for the battery
to cool down before recharging.
c) The battery in your new tool is not charged when it leaves
the plant. Therefore it must be full charged before using the
first time.
d) Please charge the battery to reach full or no less than half
charge before storage. If the tool will not be used for long
periods of time, charge the battery every 3-6 months.
CHARGING PROCEDURE (SEE FIG. B)
1) Plug the charger into an appropriate outlet. The light will
be green.
2) Slide the battery pack into the charger, the light will turn
to red to indicate the charging process has started.
3) When charging is completed, the light will turn to green.
The pack is now fully charged, unplug the charger and
remove the battery pack.
CHARGING INDICATOR
This charger is designed to detect some problems that can
arise with battery packs. Indicator lights indicate problems
(see table below). If this occurs, insert a new battery
pack to determine if the charger is OK. If the new battery
charges correctly, then the original pack is defective and
should be returned to a service center or recycling service
center. If the new battery pack displays the same problem
as the original Battery Pack, have the charger tested at an
authorized service center.
Light Status
Red on
Charging
Green on
Fully Charged
WARNING: When battery charge runs out after
continuously use or exposure to direct sunlight
or heat, allow time for the tool to cool down before re-
charging to achieve the full charge.
2. TO INSTALL OR REMOVE THE BATTERY PACK (SEE
FIG. C)
Press the battery pack release button and remove the
battery pack from the tool. After recharge, slide the battery
pack into tool’s battery port. A simple push and slight
pressure will be sufficient.
NOTE: This machine will only run when 2 batteries are
installed. It is recommended to use the same two batteries
and charge the two batteries at the same time.
OPERATION
1. STARTING/STOPPING (SEE FIG. D)
Starting
Press the on/off switch.
Stopping
Release the on/off switch.
It is also a variable speed switch that delivers higher speed
and torque with increased trigger pressure. Speed is
controlled by the amount of switch trigger depression.
WARNING: The tool runs for a few seconds after
it has been switched off. Let the motor come to
a complete standstill before setting the tool down.
2. USING THE BLOWER (SEE FIG. E)
The blower is intended for residential use only. Use the
blower outdoors to move debris from hard surfaces. This
blower is not designed to clear leaves from large grassy
areas, or move wet, heavy debris.
USER TIPS
- Hold the blow tube approx 180mm above the ground when