SET UP PROCEDURE
CISTERN FLUSHING SYSTEM
The next step is programming the Easy Flush. In cistern mode, (the most popular in UK) the set up
process involves timing how long it takes to fill your urinal flushing cistern with water, because every site
will be different due to cistern size and water pressure differences.
Firstly remove the Easy Flush from its packaging, and carefully lift the rubber gasket
(D)
over the 3 metal
valve connectors, to reveal the battery tray
(IMPORTANT ensure cistern is empty before commencing
with cistern fill time settings)
. Carefully fit the battery
(B)
observing the correct battery polarity and
replace the rubber gasket, then immediately (within 20 seconds) fit the Easy Flush
(A)
to the solenoid
valve head
(H).
Attach the M3 securing screw (
I
) and lightly tighten. Replace the screw cover
(J).
You will notice if the battery has been fitted correctly a letter
“C”
will be displayed on the front of the Easy Flush
which means it is ready to be set up for use with a cistern fed urinal.
Ensuring your cistern is still empty and the letter
“C”
is being displayed on the front of the Easy Flush, press the
“F”
button so the screen displays
“F-S”
, meaning the system is ready to start filling. Press
“F”
again which will
then open the valve and water will flow into the cistern, (while the cistern is filling a small dot will flash on the
front of the Easy Flush to indicate the cistern fill time is being recorded). Once the cistern has filled, the flush will
start at which point you simply press the
“F”
button again to record the total cistern fill time. The fill time is now
set into the Easy Flush memory.
ADJUSTING THE FLUSH CYCLE (CISTERN FLUSH SYSTEM)
The Easy Flush will now display “ T - 0 - 0”. As an example, T - 0 - 4 would mean 4 flushes per day, attained by
pressing the
“T”
button 4 times. T - 1 - 2 would mean 12 flushes per day.
After you have selected the desired amount of flushes wait 20 seconds and the display will extinguish after a “beep”
and this confirms the setting has been accepted. Your Easy Flush is now set up and will flush your urinals to the
desired rate per day until the battery expires, in approximately 2 years OR when ‘battery low’ alarm sounds.
If you fail to set-up the Easy Flush correctly, a factory default setting will be automatically selected
(6 minutes fill time, 4 flushes per day).
DIRECT FLUSHING SYSTEM
If you wish to set the Easy Flush for use with a Direct Flush System hold any button down while connecting the
battery and it will display a letter
“D”
now you have selected the Direct Flushing mode, you are ready to set up
the Easy Flush.
Ensuring the letter
“D”
is being displayed on the front of the Easy Flush press the
“F”
button so the screen
displays
“F-S”
, meaning the system is ready to start filling. Press
“F”
again which will then open the valve and
water will flow into the cistern. Press the
“F”
button again which will then open the valve and start to flush the urinal,( while the urinal
is flushing with water a small dot will flash on the front of the Eay Flush to indicate the timing is in progress) after about 5-10 seconds
you simply press the
“F”
button again to record the total urinal flush time.
Important
In Direct mode
“D”
it is only normally recommended to flush a urinal for about 5 – 10 seconds duration.
For Direct Flushing Systems you will require a larger orifice valve
(please seek advise from the manufacturer).
ADJUSTING THE FLUSH CYCLE (DIRECT FLUSH SYSTEM)
The Easy Flush will now display “ T - 0 - 0” (where T12 would mean 12 flushes per day) and this is attained by pressing the
“T”
button 12
times, after you have selected the desired amount of flushes wait 20 seconds and the display will extinguish after a “beep” and this
confirms the setting has been accepted.
Important; In Direct mode
“D”
it is only normally recommended to flush a urinal with more frequency than with a cistern due to the
lower flush volumes.
If you fail to set-up the Eay Flush correctly, a factory default setting will be automatically selected (12 x 5 second flushes per day).
CARE AND MAINTENANCE
* Only fit and use prime quality batteries such as ‘Energizer’ or ‘Duracell’
* Replace the battery every 2 years OR when ‘battery low alarm’ sounds, to ensure the product functions correctly.
* Ensure the device is always kept clean and and away from the elements as it is not designed for exterior applications.
* To check the current cistern FLUSH TIMING frequency press “T”
* For the number of FLUSHES since installation press “F”
* To RESET remove the battery and leave for approx. 10 minutes for current to drain and memory to reset or you can remove the battery and place your fingers across
the contacts whilst holding one of the buttons down for approx. 10 seconds to drain the current.
* If a TEST FLUSH is required press and keep holding “T” then at the same time press and hold the “F”, keep both buttons pressed whilst the display goes through its
software version, once it displays “UER” let go of both buttons and a test flush will be performed after which the East Flush will revert back to your previous
programming.
WARRANTY
The Easy Flush is covered by a manufacture defect 2 year warranty. We offer a 2 year part replacement only. No responsibility can be taken for failure of the device or
valve resulting from contaminated water supplies or improper installation of the device. The WES50.3 valve warranty is expressly the responsibility of the valve
manufacturer, details of which are applied for via ourselves.
For any assistance required with this product please either call your distributor or get in touch directly with the manufacturer;
Washroom Efficiency Services Ltd
TEL: UK +44 (0) 1803 521415.
Email: [email protected]
WES50
