English
ENG
ORIGINAL INSTRUCTIONS
4
ries which are not specifically designed and rec
-
ommended by Werku
®
. Just because the acces-
sory can be attached to this power tool, it does
not assure safe operation. The rated speed of the
accessory must be at least equal to the maximum
speed marked on this power tool. Accessories run-
ning faster than their rated speed can break and
fly apart. The outside diameter and the thickness
of your accessory must be within the capacity rat-
ing of this power tool. Incorrectly sized accesso-
ries cannot be adequately guarded or controlled.
Threaded mounting of accessories must match
the spindle thread. For accessories mounted by
flanges, the arbour hole of the accessory must fit
the locating diameter of the flange. Accessories
that do not match the mounting hardware of this
power tool will run out of balance, vibrate exces-
sively and may cause loss of control. Do not use
a damaged accessory. Before each use, inspect
the accessory. If this power tool or its accessory is
dropped, inspect for damage or install an undam-
aged accessory. After inspecting and installing an
accessory, position yourself and bystanders away
from the plane of the rotating accessory and run
this power tool at maximum no-load speed for one
minute. Damaged accessories will normally break
apart during this test time. Position the cord clear
of the spinning accessory. If you lose control, the
cord may be cut or snagged and your hand or arm
may be pulled into the spinning accessory. Reg-
ularly clean this power tool’s air vents. The mo-
tor’s fan will draw the dust inside the housing and
excessive accumulation of powdered metal may
cause electrical hazards.
STORE POWER TOOLS.
Store power tools out of reach of children and not
allow the handling of power tools to people unfami-
liar with the tools or these instructions. Power tools
are dangerous in the hands of untrained users.
MAINTENANCE.
Check moving parts for misalignment or binding,
there are no broken parts or other conditions that
may affect the operation of power tools. Power tools
are repaired before use when they are damaged.
Many accidents are caused by poorly maintained
power tools. Use power tools, accessories and
tool tips, etc. according to these instructions and
in the manner provided for the particular type of
power tool, taking into account the conditions work
and work to develop. The use of the power tool for
applications other than those intended could result
in a dangerous situation. Please check your power
tool serviced by a Werku
®
official repair service
using only identical replacement parts. This will
ensure the safety of the power tool is maintained.
CHECK CONDITION.
Make sure that all the screws in the demolition ham-
mer are perfectly tightened.
In cold climates or when
the demolition hammer has not been used for a pe-
riod, allow the demolition hammer to warm up by
leaving it to run empty for a few minutes, to ensure
that all internal components are perfectly lubricated.
Make sure that the possible installed accessories
are perfectly fitted in place.
BEFORE STARTING WORK.
Make sure that the demolition hammer is firmly sup
-
ported before using.
Check that no one is standing
beneath you when using the demolition hammer in
high areas.
Keep your hands away from all moving
parts of the demolition hammer.
DURING THE OPERATION.
Do not leave the demolition hammer operating
without having it firmly fixed.
Only turn it on when
you are sure you have full control over it.
Do not
point the demolition hammer at anyone while in
use.
When operating the demolition hammer will
produce vibrations.
The screws may gradua-
lly come loose, and possibly cause faults or ac-
cidents.
Keep your hands away from all moving
parts of the demolition hammer.
AT FINISH WORKING.
Do not touch the possible accessories installed
in the demolition hammer after use.
It may be hot
and cause burns.
Some materials worked with may
contain chemicals or toxic components.
Avoid in-
haling these substances or allowing them to come
into contact with your skin.
Use PPE designed to
prevent and protect against incidents of this kind.
DESCRIPTION OF THE PRODUCT.
The demolition hammer has been designed to
carry out light demolishing jobs.
Refer to this plan
to familiarize yourself with the demolition hammer
before use.
Содержание WK400610
Страница 38: ...38 WK400610 1 1 2 2 3 3 4 4 5 5 ...
Страница 39: ...39 WK400610 ...
