background image

W

E

N

S

H

IN

G C

O

N

F

ID

E

N

T

IA

L

D

O N

O

T D

IS

T

R

IB

U

T

IO

W

E

N

S

H

IN

G C

O

N

F

ID

E

N

T

IA

L

D

O N

O

T D

IS

T

R

IB

U

T

IO

IR

Link P

WS-AV2-Sender RX

IR

Link P

ANT

WS-AV2-Sender TX

7

8

ANT

Press the pairing key for 5 seconds from Transmitter and Receiver until the LED 
blinks in blue.In the pairing mode, if it were not pairing successfully in 30 
seconds, the system exits this mode automatically.If pairing is done successfully, 
both LED blinks steady from both Transmitter and Receiver suggesting they are 
connecting, the Receiver shows video output from the screen.(P7)

Pairing Methods

P7

Transmitting and receiver 
ends Long press for about 5 
seconds while”Pairing" button

Blue light blinking when pairing

Steady blue light indicates 
successful pairing And outputs
the image

Remote Controller

This AV transceiver supports IR transferring; it works well when the remote 
controller focuses on the IR receptor to control other devices remotely.(P8)

IR remote control

IR

Link P

WS-AV2-Sender RX

IR 

ANT

P8

Accessories

Adapter*2                  Signal conversion line*2                 Antenna*2(P9)

P9

 

AV2-RS485 Operation Guide

Installation

Transmitter

 1.Connect yellow terminal from signal cable to video port.Link signal cable to 
     3.5mm terminal from female connector at Transmitter.(P10)

(Yellow - Yellow)

P10

2.Put antenna into the antenna terminal at Transmitter.(P11) 

Link P

ANT

WS-AV2-Sender TX

P11

Rs485                    Power

Rs485                    Power

3.Positioned the dip switch to the desired group.(P12)

Both the transmitter and receiver 
to the same number allocated

P12

Link P

ANT

4.Connect the attached adapter to the corresponding position from the green 
    terminal bracket to make sure it’s being tightly screwed by using flat-blade 
    screwdriver.Have D+ and D- from RS-485 tightly screwed to the corresponding
    position from the green terminal bracket as shown from figure below by using 
    flat-blade screwdriver (only if it’s necessary).Link the green terminal bracket 
    to female connector from Transmitter, the LED blinks steady in yellow and the
    same time another LED blinks in blue for 1 second and goes off showing the 
    device is functioning well.(P13) 

WS-AV2-Sender TX

Blue lights 1 second, yellow lit

P13

Receiver

Rs485                    Power

1.Connect yellow terminal from signal cable to video port.Link signal cable to 
    3.5mm terminal from female connector at Receiver.(P14)

(Yellow - Yellow)

P14

Содержание WS-AV2 IR Sender RX








Отзывы: