background image

11

5. Application Notes

The Ethernet ports are fitted with overvoltage discharge protection. Internal varistors limit voltage surges to  
approx 70 V. The connecting cables of the digital I/O ports must not be longer than 30 m.

6. Mounting Instructions

When mounting and operating the junctions, the corresponding electrical and mechanical regulations, stan-
dards and safety rules must be observed. The junction must be protected against mechanical influences. The 
product must be fastened in such a way that the mounting position cannot change. The junction is designed 
for use in the industrial sector. The industrial environment is characterized in that consumers are not connected 
directly to the public low-voltage mains network. Additional measures must be taken for use in the residential 
sector, business and commercial sectors.
The table below defines the tightening torques of the plugs and fastening options for ensuring compliant and 
faultless operation.

Connection type

Tightening torque in (Nm)

M12

0.4

7/8" plug

1.5

FE ground strap

2.2±0.2

Junction Mounting

4.0±0.2

7. Initial Operation

Project planning, installation, start-up, maintenance and testing of the devices may only be carried out by quali-
fied electrical technicians familiar with the safety standards of automation technology.

Only cables and accessories that meet the standards and requirements for safety, electromagnetic 

 

compatibility and, if necessary, telecommunications terminal equipment and the specifications. In case of  
damage, the product must not be used further on. In the event of improper use, the guarantee and liability claim 
against the manufacturer shall lapse.

Information concerning which cables and accessories are approved for installation can be found at 

 

www.wenglor.com

 or are described in this manual.

Содержание EtherCAT ZAC50CN0 Series






























Отзывы: