background image

MOUNTING A MITER SAW TO THE STAND

The miter saw stand should fit most miter saws. Make sure the miter saw is unplugged from power supply before  

attempting to mount it onto the stand. Refer to the next section on Page 10 for mounting uncommon miter saws.

OPERATION

1. Remove and safely store the four plastic feet 

from underneath the base of the miter saw (Fig. 

7). If the miter saw has a stability block under-

neath the positive stop locking lever, remove 

and safely store it as well.

2. Remove the mounting brackets from the 

stand. Place the miter saw onto the saw mount-

ing brackets, making sure the front of the ma-

chine faces the locking handles. 

1. M6 Washers (Small) or M6 Washers (Large)

2. M6 Spring Washers

3. M6 Hex Nuts, or M6 Wing Nuts

4. M6 Carriage Bolts (Short) or M6 Carriage 

Bolts (Long), depending on the thickness of 

your miter saw’s base.

4. Finger tighten nuts and make sure the mi-

ter saw is securely mounted onto the mounting 

brackets (Fig. 8).

3. Attach the miter saw to the mounting brackets using four sets of the following combination from your mounting 

hardware:

Note:

 Only tighten lock nuts and screws to be finger tight at this stage, in case adjustments are needed after attach-

ing the miter saw. 

5. Hook the front of the brackets over the front of the miter stand’s main frame 

(Fig. 9).

6. Push the back of the brackets down to engage them onto the back frame (Fig. 

10).

7. Lock brackets into place by gently pressing down the locking handles (Fig. 11). 

8. To ensure the stability of the miter saw stand and the mounted machine during 

cutting operations, adjust the position of the miter saw so the fence of the miter 

saw is aligned with the center of the rear crossbar of the stand. 

9. When the miter saw is correctly positioned on the stand, securely tighten the four mounting nuts.

Fig. 8 

Fig. 9 

Fig. 10 

Fig. 11 

Fig. 12 

11

Содержание RMSA330

















Отзывы: