background image

MAINTENANCE

HIGH ALTITUDE OPERATION ABOVE 3000 FEET

The fuel system on this generator may be affected by operation at high altitudes. Proper operation can be ensured 
by installing an altitude kit at altitudes higher than 3000 feet above sea level. At elevations above 8000 feet, the 
engine may experience a decrease in performance, even with the proper altitude kit. Operating this generator 
without said kit may increase the engine’s emissions and decrease both fuel economy and performance.

The kit should be installed by a qualified mechanic. Refer to the instructions included with your altitude kit for 
more information about installation.

CLEANING THE GENERATOR

Never clean the generator when it is running! Never clean with a bucket of water or a hose.  Water can get inside 
the working parts of the generator and cause corrosion or a short circuit.

Always try to use the generator in a cool, dry place.  If the generator becomes dirty, clean the exterior with a damp 
cloth, a soft brush, a vacuum or pressurized air. 

CHECKING THE OIL

Check the oil level of the generator according to the Recommended Maintenance Schedule in Fig. 9.  The genera-
tor is equipped with an automatic shutoff to protect it from running on low oil.  The generator should be checked 
before each use for proper oil level.  This is a critical step for proper engine starting.  To check the oil level:

1. Make sure the generator is on a level surface.  

2. Open access panel. Clean around oil fill. Remove dipstick and wipe the dipstick with a clean rag. Insert the 
dipstick into the oil fill opening without screwing in. Remove the dipstick to check the oil mark. Add oil if the oil 
mark covers less than one half of the dipstick. 

3. Slowly add more oil and repeat step 2 until the oil mark reaches to the top 
of dipstick (Fig. 10).  Do not over fill the crankcase. 

4. Reinstall oil dipstick and access panel.

Fig. 10 -  Oil Fill Opening, 
Dipstick and Oil Level

19

WARNING: To prevent serious injury from fire, follow the kit installation proce-
dures in a well-ventilated area away from ignition sources. If the engine is hot from 
use, shut the engine off and wait for it to cool before proceeding. Do not smoke near 
the generator. Warranty will be void if adjustments are not made for high altitude use.

Содержание 56352



































Отзывы: