background image

OPERATION

ASSEMBLY

STARTING THE COMPRESSOR

1. Follow all instructions in the assembly guidelines outlined above before attempting to start the compressor. Do 
not start the generator until the air filter, oil cap breather and oil have been properly installed.

2. Inspect the machine components to make sure that there are no damaged or worn parts. Replace any damaged 
parts immediately. Only repair using identical replacement parts. 

3. Check that the pressure switch is turned to OFF position and the tank drain valve is closed.

4. Connect an air hose (not included) to the air line inlet (Fig. 4 - 1). Make sure the air hose is rated high enough to 
handle the max PSI of the compressor.

5. Connect the electrical plug to a power supply. NOTE: the compressor must be at least one foot from any wall or 
obstruction in a well-ventilated area in order to maximize proper air flow. Do not cover the compressor.

6. Turn the pressure switch (Fig. 4 - 3) to the ON/AUTO position to allow the compressor to automatically start up 
and shut down depending on its need for air. NOTE: make sure this switch is set to OFF before unplugging, plug-
ging in, or storing the compressor.

INSTALLING THE WHEELS

Insert  bolt  M10X1.25X57  into  the  wheel  through  the  wheel 
bracket and 10mm flat washer, then tighten with M10X1.25 hex 
nut. Repeat for both wheels.

INSTALLING THE AIR FILTER

Remove the plastic plug. Install the air filter (Fig. 2 - 1) before 
starting the air compressor.

INSTALLING THE OIL CAP BREATHER

Remove the plastic plug from the oil fill port (Fig. 2 - 3). Slowly 
fill with the provided semi-synthetic oil while observing the oil 
gauge (Fig. 2 - 4). Fill until the oil lands in the middle of the red 
circle between A and B (Fig. 3). Install the oil cap breather (Fig. 
2 - 2) before starting the air compressor.

WARNING: 

Be sure to fill with semi-synthetic com-

pressor oil before starting the machine. 

Fig. 1

Fig. 2

Fig. 3

1

2

3

4

A

B

REFILLING OIL

Check the oil level before each operation. When the oil level is below B, refill the 
compressor with semi-synthetic compressor oil until the oil reaches the center of 
the red circle in the oil gauge. Do not let oil level exceed A (Fig. 3). 

8

Содержание 2287

















Отзывы: