background image

1

Characteristics of Natural Wood

The properties of natural wood are such that it reacts to the climactic or humidity changes found in its environment. As 

much as half of the weight of freshly sawn wood is water. Wellborn cabinetry is crafted from wood that is carefully kiln-dried,  

retaining just enough moisture for proper construction and finishing. As a product of nature, solid hardwoods continue 

to react to their surroundings even after manufacturing and installation. Solid wood acts similar to a common household 

sponge in that when placed in a warm, moist environment (high relative humidity), the wood begins to expand. When placed 

in a dry, colder environment (low relative humidity), the wood contracts. This phenomenon can be controlled (but never 

 

eliminated) by humidity regulation. The cabinets’ quality and sturdiness are not affected by these natural changes.

As seasonal temperature and humidity changes occur within a house, door panels are susceptible to minor expansion and 

 

contraction. The contraction or shrinkage of door panels during low humidity periods may result in the appearance of an unfinished line 

down the length of the panel where it joins the door stile. Wellborn does not consider the appearance of a white line as a product defect 

and will not replace the doors on these grounds. Wellborn recommends the installation of a humidity control system to substantially 

reduce the possibility of expansion and contraction in all wood products in the home. If climactic conditions do not correct the situation 

automatically, obtain a Wellborn Touch-up Kit in the proper color and refer to the repair instructions on page 18 of this manual.

Storing new cabinetry for about a week in the same room where it will be installed could help the wood reach a balance with its 

surroundings. Consider a humidifier in the winter and an air conditioner in the summer to stabilize your home’s relative humidity at 25 

to 35 percent.

Due to the natural variation and aging process, minor differences may be noticed in color match when replacing doors on 

existing cabinetry or adding additional cabinetry at a later date. It is a characteristic of stained wood finishes, especially 

 

thermofoil cabinetry, to age over time when exposed to smoke, sunlight or general household chemicals and detergents.

The WellGuard Finishing System

Wellborn takes great pride and care with the finishing of our cabinetry. Years of research, partnered with development through 

Valspar, have resulted in our 24-step hand-sanded and hand-rubbed WellGuard finishing system that enhances—never hides—

the natural beauty of our fine hardwoods. Depending on wood species and finish chosen, variations may be accented or 

 

subdued. Wellborn cabinet finishes are highly resistant to moisture, abrasion and many common household chemicals. Our finishing 

process consists of four coating applications designed to provide both decorative beauty and protection to the wood surface.

The detailed steps of our finishing process enhance the natural beauty of each wood species. Hand-rubbed stains are utilized to 

uniformly achieve the maximum grain coloration that results in a beautiful yet natural look.

Protecting the beautiful appearance of the stained products is equally as important as the decorative process. Through much research 

and development in the chemistry of wood finishing come finishes that, when properly applied and baked on, form an extraordinarily 

tough, crack resistant coating. This tough protective finish exhibits a high order of resistance to various acids, bases, solvents and 

stains, all of which are commonly found in every household kitchen.

Certification

To ensure that your cabinetry will bring you years of pleasure and performance, be sure to look for cabinets bearing the Kitchen Cabinet 

Manufacturers Association’s (KCMA) seal of certification. Cabinets bearing this seal have passed nearly 60 tests for quality, from 

impact resistance and hinge durability to the ability to withstand such substances as household detergents, vinegar and oil.

In addition to meeting quality and strength requirements of the KCMA, Wellborn Cabinet, Inc., has an in-house laboratory that performs 

the same testing to ensure quality on a daily basis.

MSDS Information

Under OSHA’s Hazard Communications Standard 29 CFR 1910.1200, manufacturers of wood products, which may be processed in a 

manner that would create wood dust, are required to provide Material Safety Data Sheets and warning labels for their products. OSHA 

has concluded that warning labels and MSDS are appropriate for wood processed to create wood dust because of the health hazards 

that respiration of excess levels of such dust could cause.

Since many of our products may be cut, sanded or otherwise processed in a manner that would create wood dust, we have provided 

the required MSDS and warning labels to your Authorized Wellborn Dealer. Please contact the Authorized Wellborn Dealer from which 

you purchased your cabinets to obtain this information.

Содержание Elegant Bath series





































Отзывы: