Weldex WDAC-2308X Series, Руководство по эксплуатации

Страница: 13 / 31

④ Mirror Mode
: Mode ON is Mirror mode, Mode OFF is general screen state.
MIRROR OFF → ON → . . . .
⑤ Sharpness Control
: Use to change the contour of scene .
SHARPNESS 0 ~ 15
⑥ Brightness Control
: Adjust open and close lev el of iris in AI mode. The normal v alue is 48(50).
The smaller brightness v alue is, the darker it is, because iris is
closed more. On the contrary the bigger brightness v alue is,
the brighter it is, because iris is opened more.
BRIGHTNESS 0 ~ 99
⑦ Flickerless Mode
: Set FLICKERLESS ON to remov e the f licker of picture.
Shutter speed is f ixed as 1/100(NTSC) sec, 1/120(PAL) sec .
FLICKERLESS OFF → ON → . . . .
⑧ Max AGC control
: Set AGC lev el.
MAX AGC OFF → 8dB → 10dB → . . . . → 36dB → 38dB
⑨ INITIAL SET Mode
: Set the INITIAL SET Mode ON so that all changed data are returned to
shipping condition. Mode becomes OFF if SETUP MENU state is dif f erent
f rom shipping condition.
INITIAL SET OFF → ON → . . . .
5.6 SETUP MENU 2 f unctions
White Balance Mode
: Outer illumination condition is expressed by Color temperature ,Kelv in
(°K). It is White Balance that shows white as white in any illumination
conditions. It is composed of f iv e modes.
ATW ( Auto Trace White balance )
: do automatically under any condition in range 2,800°K ~ 8,000°K
It can be adjustable red and blue point of desired white position
INDOOR ( Indoor Preset WB )
: Use to set the preset illumination condition as 3200°K.
OUTDOOR ( Outdoor Preset WB )
: Use to set the preset illumination condition as 5400°K.
MANUAL ( Manual WB )
: Use to adjust to desired color temperature manually .
(0 ~ 99 decimal v alue )
AWC ( Auto White Control )
: Consider current illumination condition, do white balance by f orce
and lock as manual.
White Balance Mode Control
: It display s and changes White Balance Mode Control status of Camera.
ATW AUTO ( It doesn’t need to adjust. )
INDOOR 3200°K ( It doesn’t need to adjust. )
OUTDOOR 5400°K ( It doesn’t need to adjust. )
MANUAL 50 ( It can be adjust )
AWC LOCK → PUSH → . . . .
(
LOCK means Manual white balance status. Press NEAR(+) / FAR(-)
key continuously, LOCK mode becomes PUSH mode and white balance
acts automatically, and then white balance mode is locked as manual.)
Set Focus Mode
: It is composed of three modes.
AUTO : Use to f ocus automatically all the time.
MANUAL : Use to f ocus manually by pushing NEAR(+) / FAR(-)key .
Ev en though MANUAL mode, it will be f ocused in about 5 seconds af ter
zoom in(TELE) / out(WIDE), and return to MANUAL mode automatically .
This is f or f ocusing accurately af ter zooming.
ONESHOT(option) : It is similar to MANUAL mode.
But there are some dif f erence.
In case the f ocus mode is ONESHOT, it is f ocused whenev er ONESHOT
(AUTO/MANUAL key ) key is pushed. It will be returned to MANUAL mode
af ter the f ixed seconds ev en though can not be f ound best f ocus.
(Taking time is able to set in Special Menu. ) In this case
push ONESHOT(AUTO/MANUAL key ) key again, it will be in best f ocus.
PUSHAUTO(option) : While pushauto key is pushing, f ocus mode is auto.
☞
caution
1. According to Model, focus mode is Auto -> Manual -> Ones hot
or Auto -> Manual -> Pus hauto.
< Fig 5-5. SETUP MENU 2 >
<<SETUP MENU 2>>
WB MODE
WB CONT
FOCUS SET
START ZOOM
END ZOOM
ID DISPLAY
SPECIAL MENU
PREV. MENU
ATW
AUTO
ONESHOT
x1
x184
OFF
- 12 -