WeldCorp MIG 125 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 21

background image

Page 7

WELDER INFORMATION (cont.)

Through the pressure and rotation of ENC-1 it’s possible to set the following settings

shown on DISP-1:

After 3 seconds, if the knobs aren’t pushed, or the machine is in stand by mode, the display

DISP-1 shows the value set for the wire speed, while display DISP-2 shows the value set for

the power.
During the welding, DISP-1 shows the value of the welding voltage, while display DISP-2 (in

Page 8) shows the value set for the power.

«
...
6
7
8
9
10
...
»

Содержание MIG 125






















Отзывы:

Нет отзывов

Похожие инструкции для MIG 125

Bell & Gossett ecocirc XL Series

Бренд: Xylem Страницы: 62

Бренд: Zeck Audio Страницы: 16

FINISH-OUT MC111M

Бренд: M&S Systems Страницы: 2

Бренд: SMT Страницы: 24

Бренд: ESAB Страницы: 21

Maxstar 150 STL

Бренд: Miller Electric Страницы: 4

Бренд: Watts Страницы: 24

IOLAN SDG1 LA/LE

Бренд: Perle Страницы: 21

Бренд: Gude Страницы: 7

Бренд: Magmaweld Страницы: 136

Бренд: Advent Страницы: 32

Aristo RoboFeed 30-4

Бренд: ESAB Страницы: 34

Бренд: Lupus Electronics Страницы: 148

Бренд: Tuxedo Страницы: 33

Бренд: Bauhn Страницы: 28

Бренд: Pattfield Страницы: 94

Бренд: Polk Mono Страницы: 14

Бренд: Abus Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды