background image

44

THE INFORMATION HEREIN IS GIVEN IN GOOD FAITH, BUT NO WARRANTY, EXPRESS OR IMPLIES, IS MADE.

Revision Date: 02/10/04

                   Rev. 4

P/N:  67-0278A     

4 of  4

SECTION 9 – ENVIROMENTAL DATA

Section 313 – Toxic Chemicals

This product does not contain toxic chemicals of Section 313 of Title III of Supervened Amendments and
Reauthorization Act of 1986 (SARA) and 40 CFR Part 372.

Section 311 – Hazard Catagories

1.

Not Applicable

Yes

2.

Acute (Immediate Health Hazard)

No

3.

Chronic (Delayed Health Hazard)

No

4.

Fire Hazard

No

5.

Sudden Release of Pressure Hazard

No

6.

Reactive Hazard

No

Section 302(A) – Extremly Hazardous Substances

(RQ   = Reportable Quantity) 
(TPQ = Threshold Planning Quantity)
This product does not contain extremely hazardous substances of Section 302(A)

Clean Water Act

Under Section 311(b)(4) of the Clean Water Act, discharges of crude oil and petroleum products in any kind or
form to surface waters must be immediately reported to the National Response Center: 

1-800-424-8802

Comprehensive Environmental Response Compensation & Liability (Act CERCLA)
Section 102 Hazardous Substances 42 U.S.C. 9602
Petroleum and petroleum fractions are excluded from the list of CERCLA hazardous substances by Section
101(14) of CERCLA.

Federal Regulations

Reported in TSCA Inventory

Product:

Yes

Components:

Not Applicable

Information given herein is offered in good faith as accurate, but without guarantee. Conditions of use and
suitability of product for particular uses are beyond our control; all risks of use of the product are therefore
assumed by the user and 

we expressly disclaim all warranties of every kind of nature, including warranties

of merchantability and fitness for a particle purpose in respect to the use or suitability of the product

.

Nothing is intended as a recommendation for uses which infringe valid patents or as extending license under
valid patents. Appropriate warnings and safe-handling procedures should be provided to handlers and users.

ATTENTION

:

Misuse of empty containers can be hazardous. Empty containers can be hazardous if used 
to store toxic, flammable, or reactive materials. Cutting or welding of empty containers 
might cause fire, explosion or toxic fumes from residues. Do not pressurize or expose to 
open flame or heat. Keep container closed and drum bungs in place.

REGULATION INFORMATION

:

D.O.T. SHIPPING NAME:

 N/A 

D.O.T. HAZARD CLASS:

 N/A

D.O.T. IDENTIFICATION NUMBER:

 N/A

Содержание 8905















































Отзывы: