Welch 2052B-01 Скачать руководство пользователя страница 8

Page 6 

IMPORTANT NOTICE TO PURCHASER: WARRANTY 

UNPACKING 

Inspect the pump carefully. If any damage has occurred, file claim with the carrier immediately. Save the shipping container for 
carrier to inspect. 

OPERATING PUMP 

Refer to the enclosed Instruction/Operation Manual for all information to properly operate and  maintain the pump. 

WARRANTY 

This Welch Vacuum product is warranted to be free from defects in material and workmanship. 
The liability of Welch under this warranty is limited to servicing, adjusting, repairing  or replacing any unit or 
component part which in the judgment of Welch-Ilmvac has not  been misused, abused or altered in any way causing 
impaired performance or rendering     it inoperative. No other warranties are expressed or implied. The method of 
executing this warranty: servicing, adjusting, repairing or replacing shall be at the discretion of Welch. Vacuum pumps 
that have been used for any period, however short, will be repaired under this  warranty rather than replaced. 

The warranty is effective for one year from the date of original purchase when: 

1. The warranty card has been completed and returned.
2. The product is returned to the factory or other designated service centers, freight prepaid.
3. The product in our judgment is defective through no action or fault of the user.

If the product has become defective through misuse, abuse, or alteration, repairs will be billed  regardless of the age of the 
product. In this event, an estimate of the repair costs will be submitted  and authorization of these charges will be required 
before the product is repaired and returned. 

To obtain a return authorization number, please fill in the on-line request form on www.welchvacuum.com. Products without a 
return authorization number will be refused by our receiving department.  Before shipping, properly pack the pump, insure it 
against loss or damage, and on the outside of the  pump packaging and the packing slip write in the return authorization 
number. Pumps damaged due to improper packaging are the customer’s responsibility. 

Gardner Denver Thomas GmbH
Am Vogelherd 20 
98693 Ilmenau 
Germany 
T +49 3677 604 0 
F +49 3677 604 131 

[email protected]

 

www.gardnerdenver.com/de-de/welch

 

For USA, Canada and all Americas 

Gardner Denver Thomas, Inc.
1601 Feehanville 
Drive Mount Prospect, IL 60056 USA 
T  +1 847 676-8800 
F  +1 847 677-8606 

[email protected] 

www.gardnerdenver.com/de-de/welch

 

Содержание 2052B-01









Отзывы: