Welch Allyn Propaq LT 802LT0N Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 80

background image

2

5

Overview

Purpose and scope

This is a reference for periodic preventive maintenance and corrective service procedures
for the Propaq LT monitors, models 802LTAN, 802LT0N, 802LTRN, 802LTAS, 802LT0S,
and 802LTRS.

Corrective service is supported to the level of field-replaceable units. Field-replaceable
units include certain circuit-board assemblies, subassemblies, case parts, and other parts.
All field-replaceable parts are listed in

“Replacement parts”

This guide provides troubleshooting information, assembly procedures, and instructions
for functional testing and performance verification. It is intended for use only by
technically qualified service personnel.

This guide applies only to the Propaq LT monitor. For service information about any other
model of the Propaq monitor, refer to the service manual for that product.

Technical support services

Welch Allyn offers the following technical support services:

Telephone support (1-800-289-2501 and 1-503-530-7500)
Loaner equipment
Service agreements
Service training
Replacement service parts
Factory service

WARNING

When performing a service procedure, follow the instructions

exactly as presented in this manual. Failure to do so could damage the monitor,
invalidate the product warranty, and lead to serious personal injury.

Caution

No component-level repair of circuit boards and subassemblies is

supported. Use only the repair procedures described in this manual.

Note

Repair and replacement of the main board is not supported. Any service work on
the main board must be performed by certified and qualified service personnel at
an authorized Welch Allyn service center. (For contact information, see

Repair and replacement of the radio and the antenna is not supported. Any
service work on the radio and the antenna must be performed by certified and
qualified service personnel at an authorized Welch Allyn service center. (For
contact information, see

«
...
7
8
9
10
11
...
»

Содержание Propaq LT 802LT0N

















































































Отзывы:

Нет отзывов

Похожие инструкции для Propaq LT 802LT0N

Бренд: Samson Страницы: 4

Бренд: ICT Страницы: 48

Бренд: OfiTE Страницы: 67

Бренд: Bacharach Страницы: 28

Бренд: Hama Страницы: 6

Бренд: Kathrein Страницы: 10

Бренд: Sabre Страницы: 13

Бренд: Trebs Страницы: 44

Greenlee CLM-1000

Бренд: Textron Страницы: 36

Бренд: Ramsey Electronics Страницы: 40

Бренд: Solinst Страницы: 2

Бренд: Hanna Instruments Страницы: 24

Бренд: RaySafe Страницы: 2

Бренд: Trotec Страницы: 3

Бренд: HTC Страницы: 2

Бренд: RADWAG Страницы: 12

TRAVELER 3D ARM

Бренд: GRAVITY Страницы: 2

Бренд: Kawai Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды