Welbilt FRYMASTER FilterQuick FQE30 Скачать руководство пользователя

Страница: 3 / 44

DANGER

Improper installation, adjustment, maintenance or service, and unauthorized alterations or modifications can cause

property damage, injury, or death. Read the installation, operating, and service instructions thoroughly before

installing or servicing this equipment.

DANGER

No structural material on the fryer should be altered or removed to accommodate placement of the fryer under a

hood. Questions? Call the Frymaster Service Hotline at 1-800-551-8633.

DANGER

Adequate means must be provided to limit the movement of this appliance without depending on or transmitting

stress to the electrical conduit. A restraint kit is provided with the fryer. If the restraint kit is missing contact your

local KES.

NOTICE

All fryers shipped without factory supplied cords and plug assemblies must be hardwired using flexible conduit to

the terminal block located on the rear of the fryer. These fryers should be wired to NEC specifications. Hardwired

units must include installation of restraint devices.

CAUTION

No warranty is provided for any Frymaster fryer used in a mobile or marine installation or concession. Warranty

protection is only offered for fryers installed in accordance with the procedures described in this manual. Mobile,

marine or concession conditions of this fryer should be avoided to ensure optimum performance.

DANGER

The front ledge of the fryer is not a step! Do not stand on the fryer. Serious injury can result from slips or contact

with the hot oil.

DANGER

Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance.

DANGER

Do not spray aerosols in the vicinity of this appliance while it is in operation.

DANGER

Keep all items out of drains. Closing actuators may cause damage or injury.

DANGER

The crumb tray in fryers equipped with a filter system must be emptied into a fireproof container at the end of frying

operations each day. Some food particles can spontaneously combust if left soaking in certain shortening material.

WARNING

Do not bang fry baskets or other utensils on the fryer’s joiner strip. The strip is present to seal the joint between the

fry vessels. Banging fry baskets on the strip to dislodge shortening will distort the strip, adversely affecting its fit. It

is designed for a tight fit and should only be removed for cleaning.

DANGER

This fryer has a power cord (three-phase) for each frypot. Prior to movement, testing, maintenance and any repair on

your Frymaster fryer; disconnect ALL electrical power cords from the electrical power supply.

DANGER

This appliance must be connected to a power supply having the same voltage and phase as specified on the rating

plate located on the inside of the appliance door.

WARNING

All wiring connections for this appliance must be made in accordance with the wiring diagram(s) furnished with the

appliance. Refer to the wiring diagram(s) in the rear of this manual when installing or servicing this equipment.

Содержание FRYMASTER FilterQuick FQE30













































Результаты поиска

Содержание FRYMASTER FilterQuick FQE30

Отзывы:

Похожие инструкции для FRYMASTER FilterQuick FQE30

Бренды по названию

Популярные бренды

Welbilt FRYMASTER FilterQuick FQE30, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание FRYMASTER FilterQuick FQE30

Отзывы:

Похожие инструкции для FRYMASTER FilterQuick FQE30

Бренды по названию

Популярные бренды