manualshive.com logo in svg

Weir Roto-Jet RO III 3x2, Руководство по разборке и сборке

Поделиться
Скачать
Weir Roto-Jet RO III 3x2 Скачать руководство пользователя страница 27

 

 

RO/ROH 3x2 

23 

 

the rotor cover does not cock, as the o-ring might be damaged.  Torque the 
capscrews to 100 ft. lbs. 

 

2.9.6.  Endbell installation (Reference figure 2.4) 

 

2.9.6.1.  Install alignment tools (P/N 0600580573) in rotor case (31) for 

endbell/rotor case alignment.  Align endbell so that the 1/2" drain hole is 
at the bottom.  Carefully slide the endbell (26) into place.  Lubricate and 
install the nine endbell socket head capscrews (63) and torque to 104 
ft. lbs. 

 

2.9.7.  Completion

.

  Re-assemble seals and manifold per section 2.8.1 - 2.8.7. 

 
 

2.10.  Bearing Replacement 

 

WARNING:

 Before lifting the pump into the vertical position first remove the 

lifting eye and install the swivel hoist.  When tightening the swivel hoist ring, 
torque to 100ft-lbs.  Once the pump is re-assembled and in the horizontal 
position remove the swivel hoist and re-install the lifting eye.  Reference 
APPENDIX A Drawing. 

 

2.10.1. Preparation

.

  Remove pick-up tube per section 2.9.1 to 2.9.3. 

 

2.10.2. Rotor assembly removal. (Reference Figure 2.5) 

 

2.10.2.1. 

Recommended the unit be mounted vertically with the shaft 

downward and the rotor facing upward when rotor assembly is 
removed. 

 

2.10.2.2. 

Remove the driveshaft key (43). 

 

2.10.2.3. 

Remove the self locking nut (46) using a bearing locknut torque 

wrench adaptor and place bearing locknut aside to be use4d in bearing 
installation 2.10.4. 

 

Remove bearing cap slinger (27) and the three hex head bearing 
retainer capscrews (58) which secure bearing retainer to the pedestal 
(58) figure 2.4. 
 
Remove pedestal cover (18) and position oiler ring (22) to clear 
bearings when rotor assembly is being removed, figure 2.4. 
 

Содержание Roto-Jet RO III 3x2









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды