Weinzierl KNX IO 511, Руководство по эксплуатации и установке

Страница: 9 / 15

© 2019 WEINZIERL ENGINEERING GmbH Page 9/15
Function of (…) on press / short press
Function of (…) on release / long press
It is selectable for each object, which telegram is sent on open-
ing/closing the contact or on short/long button press.
- No reaction
- Switch on
- Switch off
- Toggle
Output b
Here you can show/hide the parameters and the object for out-
put b.
Q. Input B1: Dimming
On selection of function Dimming following objects are visible:
Group Object Type KNX Size Direction
GO 21 Input B1: Dimming on/off
– Switch
1.001 1 Bit

To KNX
GO 22 Input B1: Dimming relative
–
Brighter/Darker
3.007 4 Bit

To KNX
Dimming function
The dimming function parameter determines whether only one
switching / dimming direction or 1-button control is to be used:
- On / Dim brighter
- Off / Dim darker
- Toggle direction
If the input detects a short button press, a switching telegram is
sent via object 21. On long button press, a relative dimming is
sent over the entire dimming range to object 22. When releasing
after long button press, a dimming-stop telegram is sent via
object 22.
The time for detection of a long button press can be set in the
general parameters and is valid for all channels.
R. Input B1: Shutter
On selection of Shutter function following objects are visible:
Group Object Type KNX Size Direction
GO 21 Input B1: Drive start
– Up/Down
1.008 1 Bit

To KNX
GO 22 Input B1: Drive stop
– Step/Stop
1.007 1 Bit

To KNX
Shutter function
The “Shutter function” parameter determines whether only one
shutter direction or 1-button control is to be used:
- Up / Step-Stop
- Down / Step-Stop
- Toggle direction
User control
The parameter
“User control” determines the sending of tele-
grams on short and long button press:
- Long = Drive / Short = Step/Stop
Long button press: Drive command via object 21.
Short button press: Stop/step command via object 22
- Short = Drive / Short = Step/Stop
Alternately drive command via object 21 und stop/step
command via object 22 on short button press, long
button press is not evaluated
- Pressed = Drive / Release = Stop
On button press drive command via object 21, on re-
leasing the button stop/step command via object 22
The time for detection of a long button press can be set in the
general parameters and is valid for all channels.
S. Input B1: Send value
If function Send value is selected, the following telegrams can be
sent at button press:
- 1 byte - Percent value
Group Object Type KNX Size Direction
GO 21 Input B1: Send percent value (1
byte)
– Set value
5.001 1 Byte

To KNX
- 1 byte - Integer value
Group Object Type KNX Size Direction
GO 21 Input B1: Send integer value (1
byte)
– Set value
5.010 1 Byte

To KNX
- 2 byte - Integer value
Group Object Type KNX Size Direction
GO 21 Input B1: Send integer value (2
byte)
– Set value
7.001 2 Byte

To KNX
- 2 byte - Float value
Group Object Type KNX Size Direction
GO 21 Input B1: Send float value (2
byte)
– Set value
9.001 2 Byte

To KNX
- 3 byte - RGB value
Group Object Type KNX Size Direction
GO 21 Input B1: Send RGB color value
(3 byte)
– Set value
232.600 3 Byte

To KNX