Weil-McLain GOLD CGi-4E Скачать руководство пользователя

Страница: 14 / 68

GOLD

CGi-4E Gas-Fired Water Boiler — Boiler Manual

Part Number

550-110-711/1108

Venting — general information

CGi-4E venting methods — Chimney draft or Direct exhaust

Chimney draft venting

Chimney draft venting uses the natural draft provided by a ver

tical vent or chimney. Category I appliance (non-positive vent

static pressure and vent gas temperature that avoids excessive

condensate production in vent). See Section

. Chimney draft

installations use:

1. Vent connector (single or doublewall) sized to eliminate posi

tive pressure in vent system. Diameter increases immediately

at boiler.

2. Doublewall metal vent (B-vent) or chimney with liner ap

proved by the National Fuel Gas Code, ANSI Z223.1–latest

edition, or in Canada B149.1 or B149.2 Installation Code.

Direct exhaust — vertical or sidewall

Direct exhaust venting uses inside combustion air with no com

bustion air connector piping. The CGi-4E flue gas vent is pressur

ized, requiring careful sealing of all joints. Category III appliance

(positive vent static pressure and vent gas temperature that avoids

excessive condensate production in vent). See pages 15-19.

Direct exhaust installations use:

1. Vent pipe specified in this manual.

2. Vent termination through outside wall, roof or unused chim

ney. Tight chimney areas will make vent joint construction

very difficult.

Venting — chimney draft venting

1. Use doublewall metal vent (B-vent) or chimney with liner as

required by the National Fuel Gas Code, ANSI Z223.1–latest

edition, or in Canada, B149.1 or B149.2 Installation Code.

2. To prevent downdrafts, chimney should extend at least 3 feet

above the highest point where it passes through a roof and

at least 2 feet higher than any portion of a building within

a horizontal distance of 10 feet.

3. To vent with another appliance, see National Fuel Gas Code,

ANSI Z223.1–latest edition or in Canada B149.2 or B149.2

Installation Code

4. Do not connect breeching to any portion of a mechanical

draft system that can operate under positive pressure.

5. Maintain minimum 2” clearance from combustible materials

to vent pipe.

6. Do not use chimney with an open fireplace.

7. Make horizontal runs as short as possible. Long runs can

cause condensation.

8. When longer runs are used, support pipe with appropriate

hangers.

9. To prevent blockage, do not vent into bottom of chimney.

10. Vent pipe must not go beyond inside wall of chimney.
11. Vent passing through floors or ceilings must be fire

stopped.

12. See

Figure 7

and

Table 3

to connect boiler to venting sys-

tem.

Inspect existing chimney before installing boiler. Failure to

clean or replace perforated pipe or lining will cause severe

personal injury or death.

Table 3

Vent

connector

diameter

Vent sizing given in

Table 3

is only a general guideline. The

vent connector and chimney must be designed, sized and

constructed in compliance with all applicable codes. Failure to

correctly size and install the vent system could result in severe

personal injury, death or substantial property damage.

Figure 7

Chimnney

draft

venting

Boiler

model

number

“D” Minimum

vent connector

diameter

CGi-4E

5”

Содержание GOLD CGi-4E





































































Результаты поиска

Содержание GOLD CGi-4E

Отзывы:

Похожие инструкции для GOLD CGi-4E

Бренды по названию

Популярные бренды

Weil-McLain GOLD CGi-4E, Руководство пользователя

Результаты поиска

Содержание GOLD CGi-4E

Отзывы:

Похожие инструкции для GOLD CGi-4E

Бренды по названию

Популярные бренды