background image

- 8 -

 

Wiring Requirements 

 

WARNING 

Safety First!

 

Turn the power off before disconnecting modules or wires. The 
correct power supply voltage is listed on the product label. Check 
the voltage of your power source to make sure that you are using 
the correct voltage. 

Do 

NOT

 use a voltage greater than what is 

specified on the product label.

 

These devices must be supplied by a SELV source as defined in the 
Low Voltage Directive 2006/95/EC and 2004/108/EC. 

 

 

WARNING 

Safety First!

 

Calculate the maximum possible current in each power wire and 
common wire. Observe all electrical codes dictating the maximum 
current allowable for each wire size. 
If the current goes above the maximum ratings, the wiring could 
overheat, causing serious damage to your equipment.

 

 

You should also pay attention to the following points: 

 

Use separate paths to route wiring for power and devices. If power wiring 
and device wiring paths must cross, make sure the wires are perpendicular at 
the intersection point. 
NOTE: Do not run signal or communications wiring and power wiring in the 
same wire conduit. To avoid interference, wires with different signal 
characteristics should be routed separately. 

 

You can use the type of signal transmitted through a wire to determine which 
wires should be kept separate. The rule of thumb is that wiring that shares 
similar electrical characteristics can be bundled together. 

 

Keep input wiring and output wiring separated. 

 

It is strongly advised that you label wiring to all devices in the system when 
necessary. 

Grounding the Ethernet Switch 

Grounding and wire routing help limit the effects of noise due to 
electromagnetic interference (EMI). Run the ground connection from the ground 
screw to the grounding surface prior to connecting devices. 

 

ATTENTION 

This product is intended to be mounted to a well-grounded 
mounting surface such as a metal panel. 

 

 
 

Содержание IE-SW-BL05 Series















Отзывы: