background image

10

19. Remove the 3/8” Nylon Locknut (21), 3/8” x 1 3/4”

Bolt (48), and 4 1/2” Pulley (77) from one end of
the “I” Plates (78). Route the Long Cable (66)
under the Pulley and reattach the Pulley to the “I”
Plates with the Bolt and Nylon Locknut. 

Refer to the inset drawing. (Note: The Wide
Swivel Bracket [71] is attached to the Top Frame
[67]; it is shown disassembled for clarity.) Lay the
Long Cable (66) over a 3 1/2” Pulley (15). Attach
the Pulley and a Cable Trap (59) to the Wide
Swivel Bracket (71) with a 3/8” x 1 3/4” Bolt (48)
and 3/8” Nylon Locknut (21). Be sure that the
Cable Trap is turned to the indicated position.

20. Wrap the Long Cable (66) down around the 3 1/2”

Pulley (15) on the left Arm (46). Tighten the 3/8”
Nylon Locknut (21) and 3/8” x 1 3/4” Bolt (not
shown). Be sure that the Cable Trap (59) is
turned to the indicated position.

21. Note: The 4 1/2” Pulley (77) shown in this step is

preattached to the Adjustment “U” Bracket (75). 
Attach the Adjustment “U” Bracket (75) to the
Front Upright (42) with the 5/16” x 3 1/4” Bolt
(35), a 5/16” Flat Washer (8), and a 5/16” Nylon
Locknut (3). Thread the Nylon Locknut onto
the Bolt only two complete turns.

Remove the 3/8” x 1 3/4” Bolt (48), 3/8” Nylon
Locknut (21), and 4 1/2” Pulley (77) from the
Adjustment “U” Bracket (75). Wrap the Long
Cable (66) around the Pulley as shown. Reattach
the Pulley to the Adjustment “U” Bracket with the
Bolt and Nylon Locknut.

22. Wrap the Long Cable (66) up around the 3 1/2”

Pulley (15) on the right Arm (46). Tighten the 3/8”
x 1 3/4” Bolt (48) and 3/8” Nylon Locknut (not
shown). Be sure that the Cable Trap (59) is
turned to the indicated position.

Attach the 5/16” x 3” Bolt (17), two 5/16” Flat
Washers (8), and a 5/16” Jam Nut (2) to the indi-
cated hole in the Top Frame (67). 

Slide the end of the Long Cable (66) onto the
5/16” x 3” Bolt (17). Tighten another 5/16” Jam
Nut (2) onto the Bolt.

22

11

23. Hold the indicated end of the Short Cable (23)

under the 3 1/2” Pulley (15) on the Front Upright
(42). Attach the 5/16” x 3 1/2” Bolt (87), two 5/16”
Flat Washers (8), the 1” Metal Spacer (22), and a
5/16” Nylon Locknut (3) to the Front Upright as
shown. Be sure that the Short Cable is
between the Pulley and the Metal Spacer.
Tighten the 3/8” Nylon Locknut (21) and 3/8” x 
3 1/2” Bolt (not shown). 

Wrap the Short Cable (23) up around the 3 1/2”
Pulley (15) on the Pulley Plate (20). Tighten the
3/8” Nylon Locknut (21) and 3/8” x 1 3/4” Bolt
(48). Make sure that the Cable Trap (59) is in
the 6 o’clock position.

24. Remove the 3/8” Nylon Locknut (21), 3/8” x 1 3/4”

Bolt (48), and 4 1/2” Pulley (77) from the lower
end of the “I” Plates (78). Route the Short Cable
(23) over the Pulley and reattach the Pulley to the
“I” Plates with the Bolt and Nylon Locknut.

Refer to the inset drawing. Slide the Plastic
Flanged Bushing (103) onto the Weight Tube
(80). Press the Plastic Flanged Bushing into the
top Weight (25). Slide the Weight Guide Bracket
(81) onto the top of the Weight Tube. Tap the
Weight Guide Bracket with a mallet to ensure
that the Plastic Flanged Bushing is firmly in
the top Weight. 

Insert the end of the Short Cable (23) into the
upper end of the Weight Tube (80). Insert a 5/16”
x 1 1/2” Bolt (24) through the Weight Guide
Bracket (81), Weight Tube, and Short Cable.
Tighten a 5/16” Nylon Locknut (3) onto the Bolt.

IMPORTANT: The Short and Long Cables (23,
66) must be properly routed on the Pulleys,
and the Cables must be properly tightened. To
tighten the Cables, refer to TIGHTENING THE
CABLES on page 18 of this manual.

25. Attach the Backrest (41) to the Front Upright (42)

with two 1/4” x 2 1/2” Screws (43) and 1/4” Flat
Washers (10).

25

43

42

41

10

66

67

2

2

59

46

8

17

12

3

6

9

23

24

87

48

59

8

22

23

23

66

81

3

25

103

80

23

78

77

48

21

24

8

3

15

42

20

19

21

48

48

71

77

78

15

59

21

21

46

15

77

35

21

75

48

66

3

8

42

66

21

59

66

67

66

15

21

20

15

48

Содержание VIPER 2000 WESY60400
















Отзывы: