background image

Operation and Maintenance Manual and User Service Guide for Industrial Power WP10 Series Diesel Engine 

31

 

-- The filter element is damaged.  

-- After the filter element is cleaned, it still gives alarm.  

-- To replace the element after being cleaned for 3-6 times, select high-

quality ones, which can ensure the reliability of diesel engine.  
Therefore, it is suggested to purchase the origin parts.  

5.9 Use and maintenance of diesel fuel filter   

Diesel fuel filter consists of strainer and fine filter. As the time goes by, the 
dirt  or  foreign  material  becomes  increasingly  accumulated  on  the  filter 
element  surface  and  bottom  of  housing,  which  can  clog  the  element  if  it  is 
not  removed  timely.  As  a  result,  diesel  engine  can

t  be  provided  with 

sufficient fuel, reducing the power. Therefore, it is important to periodically 
maintain or clean the diesel fuel filter.  

a. 

Periodically  open  the  drain  plug  at  the  bottom  of  housing  to  drain  the 
dirty fuel or accumulated water.  

b. 

Generally,  filter  element  should  be  maintained  once  every  200-300h, 
and  shortened  if  the  fuel  quality  is  poor.  During  maintenance,  timely 
replace any damaged filter element.  

c. 

Before maintenance, block the two holes on the main element to prevent 
any  dirt  from  getting  in.  The  filter  element  should  be  cleaned  in  clean 
kerosene and diesel fuel  by a soft brush. After that, use clean kerosene 
and  diesel  fuel  to  clean  it  again.  If  conditions  permit,  use  clean 
compressed air to blow it from the inside to the outside.  

d. 

Use clean kerosene or diesel fuel to clean the inside surface of housing 
and each hole of end cover.  

e. 

Check each sealing is damaged, if so, timely replace it. 

f. 

After  maintenance  and  before  use,  check  there  is  fuel  leakage  at  each 
sealing position.  

5.10 Use and maintenance of fresh-water cooler  

The  fresh-water  cooler  for  WP10  series  diesel  engine  is  of  shell-and-tube 
heat exchanger of which principle is that the seawater flowing in the coolant 
pipe cools the fresh water circuitously going in the inside of shell. Thus that 
can  optimize  the  cooling  conditions  of  diesel  engine  and  then  improve  the 
useful life of diesel engine.  

Содержание WP10






















































Отзывы: