WEICHAI WP10 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 53

background image

Operation and Maintenance Manual and User Service Guide for Industrial Power WP10 Series Diesel Engine

19

leaked. Switch off the main power switch to deenergize the diesel engine for
avoidance leakage of electricity.

In winter or cold regions, if the diesel engine is not used for long time and
the antifreeze is not added into the coolant, open the drain valves on the heat
exchanger (sea water and fresh water) and intercooler to completely drain the
coolant, which can prevent the engine body from being frozen.

3.4 Stopping in emergency case

If abnormal conditions were appeared during the engine is running, stop the
engine  imminently.  After  engine  is  stopped  in  emergency  case,  barring  the
crankshaft for a few circles, then check whether for abnormal. In addition, as
the  engine  is  still  hot  shortly  after  stop,  scuffing  of  cylinder  or  piston  seize
should be prevented.

3.5 Operational environment

If the ambient temperature is higher than

－

15

℃

, the diesel engine can be

normally started. If the ambient temperature is within

－

15

℃

-

－

35

℃

, some

assistant equipments should be used for normal startup. If the diesel engine is
used  in  high-altitude  or  hot  regions,  their  power  will  drop.  As  the  diesel
engine is not  explosion proof, its operational  environment should be free of
inflammable and explosive.

«
...
17
18
19
20
21
...
»

Содержание WP10






















































Отзывы:

Нет отзывов

Похожие инструкции для WP10

Бренд: Mack Страницы: 303

Бренд: BAFANG Страницы: 12

Бренд: W&H Страницы: 42

Бренд: Schartec Страницы: 16

Бренд: Briggs & Stratton Страницы: 14

Бренд: fadini Страницы: 56

Бренд: ABB Страницы: 13

Бренд: Siemens Страницы: 28

6FB1203-5AT00-7MP0

Бренд: Siemens Страницы: 7

COMBIMASTER CM110/3

Бренд: Siemens Страницы: 21

Бренд: Siemens Страницы: 19

Бренд: Siemens Страницы: 24

Бренд: Siemens Страницы: 15

Бренд: Siemens Страницы: 16

Бренд: Siemens Страницы: 38

Бренд: Siemens Страницы: 24

Бренд: Siemens Страницы: 36

Бренд: Siemens Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды